APRILIA 854239 Скачать руководство пользователя страница 31

Страница: 31 / 216

Characteristic

Engine oil capacity, replacing oil filter

1200 cm³ (73.23 cu.in)

Engine oil filter

•

Drain off the engine oil completely.

•

Unscrew the engine oil filter cover (2).

•

Remove the engine oil filter cover (2)

and collect the O-ring.

•

Remove the engine oil filter.

•

Fit a new engine oil filter and be spe-

cially careful with the position of the

filter spring.

•

Screw the engine oil filter cover (2) with

O-rings.

•

Add engine oil through the fill opening

(1).

•

Screw and tighten the oil filling / drain-

age plugs.

•

Start the engine and let it run for sev-

eral minutes.

•

Stop the engine.

•

Unscrew and take out the oil filler plug

(1).

•

Check engine oil level and top up, if re-

quired.

•

Refit the oil sump guard.

BY-PASS VALVE CLEANING

•

Drain off the engine oil completely.

•

Working on the right side, unscrew and

remove the oil pressure regulating

valve (2).

Locking torques (N*m)

Oil pressure inlet conical cap - M10x1

18 Nm

(13.28 lbf ft)

MXV 450

Maintenance

MAIN - 31

Содержание 854239

























































































































































































































Результаты поиска

Содержание 854239

Отзывы:

Похожие инструкции для 854239

Бренды по названию

Популярные бренды

APRILIA 854239, Руководство по обслуживанию станции

Результаты поиска

Содержание 854239

Отзывы:

Похожие инструкции для 854239

Бренды по названию

Популярные бренды