APRILIA 854239 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 216

background image

•

Place the vehicle upright and keep the handlebar right.

•

Make sure the fluid level in the reservoir (1) is above the 'MIN' level reference mark.

MIN

= minimum level

MAX

= maximum level

If the fluid does not reach at least the "

MIN

" level reference mark:

•

Check brake pads and discs for wear.

If the pads and/or the disc do not need replacing,

top-up the fluid.

CAUTION

FLUID LEVEL DECREASES GRADUALLY AS BRAKE
PADS WEAR DOWN.

REAR BRAKE

•

Place the vehicle upright

•

Make sure the fluid level in the reser-

voir (2) is above the "MIN" level refer-

ence mark.

If the fluid does not reach at least the "

MIN

" level reference mark:

•

Check brake pads and discs for wear.

If the pads and/or the disc do not need replacing, top-up the fluid.

CAUTION

FLUID LEVEL DECREASES GRADUALLY AS BRAKE PADS WEAR DOWN.

Top-up

CAUTION

RISK OF BRAKE FLUID SPILLING. DO NOT PULL THE BRAKE LEVER WHEN THE SCREWS ARE
LOOSE OR, MAINLY WHEN THE BRAKE FLUID RESERVOIR COVER HAS BEEN REMOVED.
PLACE A CLOTH UNDER THE BRAKE FLUID RESERVOIR TO PROTECT IT AGAINST ANY FLUID
SPLASHES.

FRONT BRAKE

•

Undo the screws (1) of the brake fluid reservoir using a short Phillips screwdriver.

CAUTION

AVOID PROLONGED AIR EXPOSURE OF THE BRAKE FLUID. BRAKE FLUID IS HYGROSCOPIC
AND ABSORBS MOISTURE WHEN IN CONTACT WITH AIR. LEAVE THE BRAKE FLUID RESER-
VOIR OPEN ONLY FOR THE TIME NEEDED TO COMPLETE THE TOPPING UP PROCEDURE.

Maintenance

MXV 450

MAIN - 38

«
...
36
37
38
39
40
...
»

Содержание 854239

























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 854239

Бренд: hepco & becker Страницы: 5

Бренд: Saddlemen Страницы: 3

Бренд: Paaschburg & Wunderlich Страницы: 2

SEMIFAIRING BATWING SML TOURING

Бренд: PUIG Страницы: 3

Бренд: Mallory Страницы: 3

Бренд: axel joost elektronik Страницы: 2

Бренд: Yamaha Страницы: 220

Бренд: Yamaha Страницы: 402

Бренд: Yamaha Страницы: 402

Бренд: Yamaha Страницы: 176

Бренд: DYNATEK Страницы: 11

Бренд: hepco & becker Страницы: 3

ACCESORIES 2005

Бренд: Triumph Страницы: 6

Clothing Range 2006

Бренд: Triumph Страницы: 19

2007 ROCKET III

Бренд: Triumph Страницы: 20

Бренд: Triumph Страницы: 136

Speed Triple 1200 RS

Бренд: Triumph Страницы: 184

Scrambler 1200 XC

Бренд: Triumph Страницы: 640

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды