APRILIA 854239 Скачать руководство пользователя страница 55

Страница: 55 / 216

•

open circuit, shorted to positive, shorted to negative.

Troubleshooting

•

Disconnect the connector from the Stepper motor and check the electrical specifications: if

NOT OK, replace the Stepper motor; if OK, check the Stepper motor connectors and the

Walbro control unit connector. If they are not OK, restore the connectors; if OK, check if

there is continuity between PIN B1 of the control unit connector and PIN A of the Stepper

motor connector. if NOT OK, restore; if OK, check if there is continuity between PIN D1 of

the control unit connector and PIN C of the Stepper motor connector, if NOT OK, restore, if

OK check if there is continuity between PIN A1 of the control unit connector and PIN D of

the Stepper motor connector. If NOT OK, restore; if OK, check if there is continuity between

PIN C1 of the control unit connector and PIN B of the Stepper motor connector, if NOT OK,

restore; if OK check that there is no short circuit to ground or to positive of one of the 4 cables

of the idle motor (white/black, white/brown, white/green, white/blue). If NOT OK, restore; if

OK, replace the WALBRO control unit

Fuses

CAUTION

NEVER ATTEMPT TO REPAIR FAULTY FUSES. NEVER USE A FUSE OF A RATING OTHER THAN
SPECIFIED. THIS COULD DAMAGE THE ELECTRICAL SYSTEM OR CAUSE A SHORT CIRCUIT,
WITH THE RISK OF FIRE.

CAUTION

IF A FUSE BLOWS OUT FREQUENTLY, THAT MAY BE DUE TO A SHORT CIRCUIT OR OVER-
LOAD. IF THIS OCCURS, CONTACT AN Official Aprilia Dealer.

Checking the fuse is necessary whenever an electrical component fails to operate or is malfunctioning

or when the engine does not start.

To check:

•

Remove the air filter.

•

Remove the fuse and check if the fila-

ment is broken.

•

Before replacing the fuse, find and

solve, if possible, the reason that

caused the problem.

•

If the fuse is damaged, replace it with

one of the same amperage.

•

Refit the air filter.

NOTE

MXV 450

Electrical system

ELE SYS - 55

Содержание 854239

























































































































































































































Результаты поиска

Содержание 854239

Отзывы:

Похожие инструкции для 854239

Бренды по названию

Популярные бренды

APRILIA 854239, Руководство по обслуживанию станции

Результаты поиска

Содержание 854239

Отзывы:

Похожие инструкции для 854239

Бренды по названию

Популярные бренды