APRILIA 854239 Скачать руководство пользователя страница 36

Страница: 36 / 216

•

Shut off the engine and wait until it

cools off.

•

Park the vehicle on firm and level

ground.

•

Keep the vehicle upright with the two

wheels on the ground.

•

Turn the radiator cap (1) anticlockwise

just one click.

•

Wait a few seconds so that possible

pressure in the circuit may be purged.

•

Turn the radiator cap (1) anticlockwise

again and remove it.

•

Check that the liquid covers the radia-

tor plates completely. Otherwise, top-

up.

When the external temperature drops below zero degrees centigrade, check the cooling system fre-

quently and add more antifreeze solution if needed (up to 60% max.).

Use distilled water in the coolant mixture to avoid damaging the engine.

Top-up

CAUTION

WAIT FOR THE ENGINE TO COOL DOWN BEFORE CHECKING OR TOPPING-UP THE COOLANT
LEVEL.

If topping-up is necessary after the check, do as

follows:

•

Remove the radiator cap (1).

•

Loosen the bleed valve (2) located on

the left radiator.

•

Tilt the vehicle to the left.

•

Top-up with coolant through the radia-

tor cap (1) until fluid comes out through

the bleed valve (2).

•

Close the bleed valve (2).

•

Place the vehicle upright with the two

wheels on the ground.

Maintenance

MXV 450

MAIN - 36

Содержание 854239

























































































































































































































Результаты поиска

Содержание 854239

Отзывы:

Похожие инструкции для 854239

Бренды по названию

Популярные бренды

APRILIA 854239, Руководство по обслуживанию станции

Результаты поиска

Содержание 854239

Отзывы:

Похожие инструкции для 854239

Бренды по названию

Популярные бренды