APRILIA 854239 Скачать руководство пользователя страница 76

Страница: 76 / 216

•

Working from the right side, unscrew

and remove the upper nut.

•

From the opposite side, slide off the

screw.

•

Collect the spacers.

•

Lower the engine.

•

After removing the engine, operate on the engine block and place it on the corresponding

engine support plate.

Specific tooling

9100841

Engine support

Installing the engine to the vehicle

•

Place the engine block.

•

Move the engine with small alternating

movements until it is perfectly aligned

with the fixing holes.

•

Fit the swingarm pin.

•

Insert the upper screw, fit the washers

and tighten the nut.

Engine from vehicle

MXV 450

ENG VE - 76

Содержание 854239

























































































































































































































Результаты поиска

Содержание 854239

Отзывы:

Похожие инструкции для 854239

Бренды по названию

Популярные бренды

APRILIA 854239, Руководство по обслуживанию станции

Результаты поиска

Содержание 854239

Отзывы:

Похожие инструкции для 854239

Бренды по названию

Популярные бренды