APRILIA 854239 Скачать руководство пользователя страница 128

Страница: 128 / 216

•

Fit the timing chain tensioner, follow

the instructions below:

•

1- Release the chain tensioner one-

way cam and push its rod completely

into the chain tensioner housing.

•

2- Fit the tensioner in the proper seat

on the timing system side of the cylin-

der head by tightening both screws to

the pre-set torque.

•

3- Fit the spring and the threaded cap

of the timing chain tensioner by tight-

ening the cap to the pre-set torque.

•

Proceed to time camshaft.

•

Position the valve cover together with

the gasket.

•

Tighten the two screws (1) and the two

fixing stud bolts (2) together with the O-

rings or new gaskets.

See also

Timing

Installing the head cover

In case of replacing the blow-by pipe of the head

cover, restore the inclination angle.

Use Loctite 243 on the threaded elements.

The tightening torque is 20 Nm (14.75 lbf ft)

Crankcase - crankshaft

Engine

MXV 450

ENG - 128

Содержание 854239

























































































































































































































Результаты поиска

Содержание 854239

Отзывы:

Похожие инструкции для 854239

Бренды по названию

Популярные бренды

APRILIA 854239, Руководство по обслуживанию станции

Результаты поиска

Содержание 854239

Отзывы:

Похожие инструкции для 854239

Бренды по названию

Популярные бренды