manualshive.com logo in svg

Applied Innovation AISwitch AI2524, Руководство пользователя

Поделиться
Скачать
Applied Innovation AISwitch AI2524 Скачать руководство пользователя страница 95

Chapter 6: Using the System Configuration Dialog

August 1997

Page 6-1

2524UM

Chapter 6: Using the System 

Configuration Dialog

Introduction

This chapter describes the System Configuration Dialog process using 
a sample configuration.  The System Configuration Dialog can be 
manually used to configure the router instead of using AutoInstall.  

System 
Configuration 
Dialog

If you do not plan to use AutoInstall (refer to the 

Using AutoInstall

 

chapter), make sure all the WAN cables are disconnected from the 
router. This will prevent the router from attempting to the run the Au-
toInstall process. The router will attempt to run AutoInstall whenever 
you power it on if there is a WAN connection on both ends and the 
router does not have a configuration file stored  in NVRAM. It can take 
several minutes for the router to determine that AutoInstall is not set 
up to a remote TCP/IP host.

If your router does not have a configuration (setup) file and you are not 
using AutoInstall, the router will automatically start the setup com
mand facility. An interactive dialog called the System Configuration 
Dialog appears on the console screen. This dialog helps you navigat
through the configuration process by prompting you for the configura-
tion information necessary for the router to operate.

Many prompts in the System Configuration Dialog include default re-
sponses, which are included in square brackets following the question. 
To accept a default answer, press <Enter>. Otherwise, type your re-
sponse.

This section gives an example configuration using the System Config-
uration Dialog. When you are configuring your router, respond as ap
propriate for your network.

At any time during the System Configuration Dialog, you can request 
help by typing a question mark (?) at a prompt.

Before proceeding with the System Configuration Dialog, obtain from 
your system administrator the node addresses and the number of bits 

Содержание AISwitch AI2524



































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды