Applied Innovation AISwitch AI2524 Скачать руководство пользователя страница 231 | Manualshive

Страница: 231 / 418

Applied Innovation AISwitch AI2524 Скачать руководство пользователя страница 231

Chapter 11: AI2524 Sync PPP Configuration Steps

August 1997

Page 11-5

2524UM

4.

In interface configuration mode, configure Terminal Access Con-
troller Access Control System (TACACS) on a specific interface
as an alternative to global host authentication:

ppp use-tacacs [single-line]

or

aaa authentication ppp

Use the

ppp use-tacacs

command with TACACS and Ex-

tended TACACS. Use the

aaa authentication ppp

com-

mand with Authentication, Authorization, and Accounting
(AAA)/.

Example: CHAP with an Encrypted Password

These configuration examples enable CHAP on interface serial 0 of
three devices.

1.

Configure Router yyy.

hostname yyy

interface serial 0

encapsulation ppp

ppp authentication chap

username xxx password secretxy

username zzz password secretzy

2.

Configure Router xxx.

hostname xxx

interface serial 0

encapsulation ppp

ppp authentication chap

username yyy password secretxy

username zzz password secretxz

«
...
229
230
231
232
233
...
»

Содержание AISwitch AI2524



































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды