Applied Innovation AISwitch AI2524 Скачать руководство пользователя страница 216

Страница: 216 / 418

AI2524 Router Card User’s Manual

Page 9-58

August 1997

2524UM

Display both ES and IS neighbors.

show clns neighbors [

type number ] [detail]

List the protocol-specific information for each IS-IS or ISO IGRP
routing process in this router.

show clns protocol [

domain | area-tag]

Display all the destinations to which this router knows how to
route packets.

show clns route [

nsap]

Display information about the CLNS packets this router has seen.

show clns traffic

Display the IS-IS link state database.

show isis database [level-1] [level-2] [l1]

[l2] [detail] [

lspid]

Display the IS-IS Leve l1 routing table.

show isis routes

Display a history of the SPF calculations for IS-IS.

show isis spf-log

Display all route maps configured or only the one specified.

show route-map [

map-name]

Discover the paths taken to a specified destination by packets in
the network.

trace clns

destination

Display the routing table in which the specified CLNS destination
is found.

which-route {

nsap-address | clns-name}

Содержание AISwitch AI2524



































































































































































































































































































































































































































Результаты поиска

Содержание AISwitch AI2524

Отзывы:

Бренды по названию

Популярные бренды

Applied Innovation AISwitch AI2524, Руководство пользователя

Результаты поиска

Содержание AISwitch AI2524

Отзывы:

Бренды по названию

Популярные бренды