manualshive.com logo in svg

Applied Innovation AISwitch AI2524, Руководство пользователя

Поделиться
Скачать
Applied Innovation AISwitch AI2524 Скачать руководство пользователя страница 357

Chapter 13: AI2524 Frame Relay Configuration Steps

August 1997

Page 13-41

2524UM

In interface configuration mode, configure an IP map to use Cisco 
encapsulation and TCP/IP header compression: 

frame-relay map ip 

ip-address dlci  

[broadcast] cisco tcp headercompression 

{active | passive}

The default encapsulation is cisco.

Note:

An interface that is configured to support TCP/IP header 
compression cannot also support priority queuing or 
custom queuing.

Configure an Interface for TCP/IP Header Compression

You can configure the interface with active or passive TCP/IP header 
compression. Active compression, the default, subjects all outgoing 
TCP/IP packets to header compression. Passive compression subjects 
an outgoing packet to header compression only if the packet had a 
compressed TCP/IP header when it was received on that interface.

In interface configuration mode, apply TCP/IP header compression to 
an interface:

1.

Configure Cisco encapsulation on the interface. 

encapsulation frame-relay

2.

 Enable TCP/IP header compression on the interface.

 frame-relay ip tcp header-compression 

[passive]

Note:

If an interface configured with Cisco encapsulation is 
later configured with IETF encapsulation, all TCP/IP 
header compression characteristics are lost. To appl
TCP/IP header compression over an interface configured 
with IETF encapsulation, you must configure individual 
IP maps, as described in the section 

Configure an 

Individual IP Map for TCP/IP Header Compression

.

Содержание AISwitch AI2524



































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды