manualshive.com logo in svg

Applied Innovation AISwitch AI2524, Руководство пользователя

Поделиться
Скачать
Applied Innovation AISwitch AI2524 Скачать руководство пользователя страница 79

Chapter 5: Using AutoInstall

August 1997

Page 5-13

2524UM

5.

 Save the configuration file to your startup configuration. This step 
saves the configuration to NVRAM. 

copy running-config startup-config

Typically, the local-area network (LAN) interface and IP address ar
already configured on the existing router. You might need to configur
an IP helper address if the TFTP server is not on the same network as 
the new router.

In this example, the existing router's configuration file contains the 
commands needed to configure the router for AutoInstall on an Ether-
net interface:

Router# configure terminal

interface Ethernet 0

   ip address 172.31.10.1 255.255.255.0

   ip helper-address 172.31.20.5

   Ctrl-Z 

Router(config)# copy running-config startup-config

Use a Frame Relay-Encapsulated Serial Interface Connection

To set up AutoInstall via a serial line with Frame Relay encapsulation, 
you must configure the existing router. Perform these tasks, beginning 
in global configuration mode:

1.

Configure the serial interface that connects to the new router, and 
enter interface configuration mode. 

interface serial 0

2.

Configure Frame Relay encapsulation on the interface that con-
nects to the new router. 

encapsulation frame-relay

3.

Create a Frame Relay map pointing back to the new router, or 
point-to-point subinterfaces, assign a data link connection identi-
fier (DLCI) to the interface that connects to the new router, and 
provide the IP address of the serial port on the new router. 

frame-relay map ip 

ip-address dlci

or 

frame-relay interface-dlci 

dlci option  

[protocol ip 

ip-address ]

Содержание AISwitch AI2524



































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды