manualshive.com logo in svg

Applied Innovation AISwitch AI2524, Руководство пользователя

Поделиться
Скачать
Applied Innovation AISwitch AI2524 Скачать руководство пользователя страница 367

Chapter 14: T1 Interface Configuration Steps

August 1997

Page 14-1

2524UM

Chapter 14: T1 Interface Configuration 

Steps

Introduction

This chapter describes how to configure the AI2524 for fractional T1.

Configure 
Fractional T1

Configuration Overview

This section describes how to configure fractional T1 and T1 (FT1/T1
service modules installed the AI2425 router. The tasks associated with 
configuring T1 include:

z

Specify the Clock Source

z

Enable Data Inversion Before Transmission

z

Specify the Frame Type of a FT/T1 Line

z

Specify the CSU Line Build Out

z

Specify FT1/T1 Line-Code Type

z

Enable Remote Alarms

z

Enable Loopcodes that Initiate Remote Loopbacks

z

Specify Timeslots

Specify the Clock Source

To specify the clock source for the FT1/T1 CSU/DSU internal clock 
or the line clock, type this in interface configuration mode:

service-module t1 clock source {internal | 

line}

Enable Data Inversion Before Transmission

Data inversion is used to guarantee the T1s density requirement on an 
AMI line when using bit-oriented protocols such as High-Level Data 
Link Control (HDLC), Point-to-Point Protocol (PPP), X.25, and 
Frame Relay.

Содержание AISwitch AI2524



































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды