manualshive.com logo in svg

Applied Innovation AISwitch AI2524, Руководство пользователя

Поделиться
Скачать
Applied Innovation AISwitch AI2524 Скачать руководство пользователя страница 200

AI2524 Router Card User’s Manual

Page 9-42

August 1997

2524UM

ES-IS protocol. The router dynamically discovers all ESs running the 
ES-IS protocol. ESs that are not running the ES-IS protocol must be 
configured statically.

It is sometimes desirable for a router to have a neighbor configured 
statically rather than learned through ES-IS, ISO IGRP, or IS-IS.

Warning: It is necessary to use static mapping only for ESs that do 

not support ES-IS. The Cisco IOS software continues to 
dynamically discover ESs that do support ES-IS. If you 
have configured interfaces for ISO IGRP or IS-IS, the 
ES-IS routing software automatically turns on ES-IS for 
those interfaces.

In interface configuration mode, enter static mapping information be-
tween the NSAP protocol addresses and the subnetwork point of at
tachment (SNPA) addresses (media) for ESs or ISs, as needed:

z

Configure all end systems that will be used when you manually 
specify the NSAP-to-SNPA mapping. 

clns es-neighbor 

nsap snpa

z

Configure all intermediate systems that will be used when you 
manually specify the NSAP-to-SNPA mapping. 

clns is-neighbor 

nsap snpa

For more information, refer to 

Configure CLNS over WANs

.

Warning: The SNPA is a data link layer address (such as an Ether-

net address, X.25 address, or Frame Relay DLCI address) 
used to configure a CLNS route for an interface.

Содержание AISwitch AI2524



































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды