manualshive.com logo in svg

Applied Innovation AISwitch AI2524, Руководство пользователя

Поделиться
Скачать
Applied Innovation AISwitch AI2524 Скачать руководство пользователя страница 253

Chapter 11: AI2524 Sync PPP Configuration Steps

August 1997

Page 11-27

2524UM

Note:

The MMP feature uses VPDN to connect multiple PPP 
sessions for which individual dial-in calls have arrived on 
different stack group members. VPDN provides speed and 
reliability for the setup and shutdown of Multilink PPP.

Complete these steps to create a a VPDN connection between a remote 
user and the home LAN:

1.

The remote user initiates a PPP connection to the ISP using the an-
alog telephone system or ISDN.

2.

The ISP network access server accepts the connection.

3.

The ISP network access server authenticates the end user with 
CHAP or PAP. The username is used to determine whether the 
user is a VPDN client. If the user is not a VPDN client, the client 
accesses the Internet or other contacted service.

4.

The tunnel endpoints—the network access server and the home 
gateway—authenticate each other before any sessions are at
tempted within a tunnel.

5.

If no L2F tunnel exists between the network access server and the 
remote user’s home gateway, a tunnel is created. Once the tunnel 
exists, an unused slot within the tunnel is allocated.

6.

The home gateway accepts or rejects the connection. Initial setup 
can include authentication information required to allow the home 
gateway to authenticate the user.

7.

The home gateway sets up a virtual interface. Link-level frames 
can now pass through this virtual interface through the L2F tunnel.

Figure 11-2

 illustrates a VPDN connection from a remote user, who 

makes a local call, to the corporate network, through an end-to-end 
L2F tunnel (shown by the dotted line).

Содержание AISwitch AI2524



































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды