manualshive.com logo in svg

Applied Innovation AISwitch AI2524, Руководство пользователя

Поделиться
Скачать
Applied Innovation AISwitch AI2524 Скачать руководство пользователя страница 370

AI2524 Router Card User’s Manual

Page 14-4

August 1997

2524UM

Super Frame configured, the remote alarm condition is signalled out 
of band in the facility data link.

You can see if the FT1/T1 CSU/DSU is receiving a remote alarm (yel-
low alarm) by issuing the 

show service-module

 command.

To disable remote alarms, type this in interface configuration mode:

no service-module t1 remote-alarm-enable

Enable Loopcodes that Initiate Remote Loopbacks

To configure the remote loopback code used to transmit or accept CSU 
loopback requests, and type this in interface configuration mode:

service-module t1 remote-loopback full

To configure the loopback code used by the local CSU/DSU to gener-
ate or detect 

payload-loopback

 commands, type this in interface 

configuration mode:

service-module t1 remote-loopback payload 

[alternate | v54]

Note:

By entering the 

service-module t1 remote-

loopback

 command without specifying any keywords, 

you enable the standard-loopup codes, which use a 1-in-5 
pattern for loopup and a 1-in-3 pattern for loopdown.

You can simultaneously configure the 

full

 and 

payload

 loopback 

points. However, only one loopback payload code can be configured 
at a time. For example, if you configure the

 service-module t1 

remote-loopback payload alternate

 command, a pay-

load v.54 request, which is the industry standard and default, cannot b
transmitted or accepted. Full and payload loopbacks with standard-
loopup codes are enabled by default.

The 

no

 form of this command disables loopback requests. For exam-

ple, the 

no service-module t1 remote-loopback full 

command ignores all full-bandwidth loopback transmissions and re-
quests. Configuring the no form of the command may not prevent telco 
line providers from looping your router in esf mode, because fractional 
T1/T1 telcos use facilities data-link messages to initiate loopbacks.

If you enable the 

service-module t1 remote-loopback

 

command, the 

loopback remote

 commands on the FT1/T1 CSU/

DSU module will not be successful.

Содержание AISwitch AI2524



































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды