ANK DAC5.1 Signature Скачать руководство пользователя страница 6

Страница: 6 / 104

2 -

About ANKits

AudioNote UK started out in the early 90’s developing several DIY audio kits while they were

building up their finished product business. DIY Audio has a long history and it was a chance for

knowledgeable customers to take advantage of world class designs and components!

AudioNote was focused on using the very finest materials and custom made components to

their specifications across the entire product line – from customer film and electrolytic

capacitors to tantalum resistors, transformers, binding posts, wires, etc… The Kit1 300B Single

Ended integrated amplifier was born during development of the Meishu and it proved to be

extremely popular worldwide. The ANKit business was born! As the finished product business

and dealer network started to flourish, AudioNote eventually broke the kit business off into a

separate division, thus in 2004, AudioNoteKits started up and was supported by a website such

that customers not located near AudioNote dealers could now order kits and have them

shipped direct. Kit development continued in earnest during the 2000’s with development

assisted by AudioNote engineering. AudioNote parts were used throughout the kits depending

on the various levels and budgets. By 2013, ANK AudioKits had a strong product range covering

all the areas of two channel audio:

Single Ended 300B product line, EL34 & EL34 classAB and

single ended product line, Digital to Analog Converters, Pre-Amplification, Phono stages and

AudioNote Speaker kits

. The end result is that customers worldwide with DIY skills can build an

entire high end audio system to their liking.
With the products getting to higher and higher levels in 2013 with the release of the Level 5

Mentor and DAC5.1, some customers wanted these high end products but wanted a

professional builder to assemble them. ANKits began offering this service for Level 4 & 5

products so that a significant investment in a kit could be turned into a work of art!
Since ANKits was born in 2004, over 2500 kits have been shipped worldwide to all corners of

the globe. There is a good demand for high end audio kits and ANKits has been delivering the

goods now for over a decade. We expect you to have a great experience building your kit and

look forward to hearing from you about your experience.
Regards

Brian Smith – Director ANKits

Содержание DAC5.1 Signature









































































































Результаты поиска

Содержание DAC5.1 Signature

Отзывы:

Похожие инструкции для DAC5.1 Signature

Бренды по названию

Популярные бренды

ANK DAC5.1 Signature, Руководство по монтажу

Результаты поиска

Содержание DAC5.1 Signature

Отзывы:

Похожие инструкции для DAC5.1 Signature

Бренды по названию

Популярные бренды