ANK DAC5.1 Signature Скачать руководство пользователя страница 9

Страница: 9 / 104

5 -

Skills / Prerequisites

We have learned a lot over the last decade from customers and here I would like to share some

tips with you to ensure a successful project. Please read through this section thoroughly, it will

give you a good idea of what is ahead and ensure your success!

5.1

Hardware/Mechanical

Not all of us are mechanically oriented, that is fine. The kit is quite well laid out such that all the

hardware is provided and bagged in individual sections so everything should make sense. Start

thinking mechanically because 30% of the kit is mechanical.
First thing to remember is that good hardware is beautiful; we use all stainless steel Metric

hardware in the kits. It truly is a thing of beauty, don’t rush your hardware!!
A few things we must understand first are:

We use the British Metric Hardware (M3 M4 M5 screw size 10mm, 15mm, etc..) as

opposed to the American Imperial system (5/1000th or 50/1000th, 1 inch ¾ inch).

Familiarize yourself with some of the hardware in the kit.

II.

The screws will be called M3 or M4 and this is the diameter of the shaft. The length of

the shaft will be in millimeters, so you would need an M4 screw 16mm and then the

option is a PAN head which is a round spherical head or a COUNTERSUNK or FLAT head.

This would be used when a screw head needs to be flush with a surface (for example

under a transformer!).

III.

So if you are asked to use an M3 16mm CSK screw, this is a M3 size obviously which is a

thinner shaft diameter than an M4. 16mm is the length of the shaft, and the head type

is CSK which is countersunk or FLAT head.

IV.

Once you have the screws handled, we can look at the matching nuts such as M4 nut or

M3 nut and corresponding washers.

Standoffs are common in the kits (again, they are either M3 or m4 size). They are

threaded typically so the screw goes into them; we use several different lengths in the

kit.

VI.

If any of the hardware is confusing or something is not fitting right, please email us.

Tool: A little patience

Содержание DAC5.1 Signature









































































































Результаты поиска

Содержание DAC5.1 Signature

Отзывы:

Похожие инструкции для DAC5.1 Signature

Бренды по названию

Популярные бренды

ANK DAC5.1 Signature, Руководство по монтажу

Результаты поиска

Содержание DAC5.1 Signature

Отзывы:

Похожие инструкции для DAC5.1 Signature

Бренды по названию

Популярные бренды