ANK DAC5.1 Signature Скачать руководство пользователя страница 17

Страница: 17 / 104

7.3.2

Connecting the White wires

Figure 3 - White Wires to PCB

Take the white wires as shown from each mains and wire to the PCB – We suggest that you

strip the end of the white wire to an appropriate length. Give yourself a little slack and then tin

the end of the wires by adding solder to the exposed wire so that the solder melts to it, then

clip the tinned wire to a length of maybe ¼” so that it can fit through the hole and then SOLDER

from the bottom of the board. You might have your own system but that should be the best

way to go. Obviously you will want to make these connections while the Board is NOT secured

to the rear of the chassis. We would also recommend that you solder on the top as well, make

sure that you leave 1-2mm of room for the exposed tinned wire to be visible so that the solder

will stick to it.

A common beginner mistake would be to push the wire into the hole but then the insulation of

the wire is pressing against the pad, this is bad form so take our advice and have a really good

smooth solder connection on top and bottom of the board for these mains primary wires.

Содержание DAC5.1 Signature









































































































Результаты поиска

Содержание DAC5.1 Signature

Отзывы:

Похожие инструкции для DAC5.1 Signature

Бренды по названию

Популярные бренды

ANK DAC5.1 Signature, Руководство по монтажу

Результаты поиска

Содержание DAC5.1 Signature

Отзывы:

Похожие инструкции для DAC5.1 Signature

Бренды по названию

Популярные бренды