ANK DAC5.1 Signature Скачать руководство пользователя страница 96

Страница: 96 / 104

19 -

Installing the Rotary ON/OFF Switch ( Optional )

We suggest that before installing the rotary on off switch at the front you verify that the

Mentor is working properly first – then if all good and you wish to install the on off switch at the

front follow the instructions – if you just want to have a place holder at the front you can install

the rotary switch and place the knob on it for aesthetic reasons and not use this switch and just

use the rear rocker switch for on off power!
Here is the idea of the on off rotary!
The mentor comes with two on off switches – there is a rocker switch at the back of the unit

and an optional ON off switch at the front – the idea is that you can leave the rocker switch at

the back of the unit in the ON position permanently and control the ON off from the switch at

the front – this is just for convenience sake if you prefer to switch power on and off from the

front of the unit
This rotary switch is installed in the front right position on the chassis – remove all the

hardware as shown!

Figure 72 - Disassembled Rotary Switch

Then position on the front of the chassis as shown in

Figure 73

Figure 74

Содержание DAC5.1 Signature









































































































Результаты поиска

Содержание DAC5.1 Signature

Отзывы:

Похожие инструкции для DAC5.1 Signature

Бренды по названию

Популярные бренды

ANK DAC5.1 Signature, Руководство по монтажу

Результаты поиска

Содержание DAC5.1 Signature

Отзывы:

Похожие инструкции для DAC5.1 Signature

Бренды по названию

Популярные бренды