ANK DAC5.1 Signature Скачать руководство пользователя страница 64

Страница: 64 / 104

12.1

Connecting the Coaxial Cable from SPDIF to the CON1

Port

Figure 40 - Digital Board installed in position

With the super regulator board completed and in position, we are going to now position the

Digital Board. This board has been built and tested at the ANK factory and will be located in an

anti-static bag. There are 5 holes that secure the digital board, the hole that is unpainted and

closest to the rear of the chassis will be the first hole to find.
We are actually going to just introduce a couple of connections to the digital board before

positioning in the chassis that we will be installing later.

Connect the Coaxial cable from the SPDIF input to CON1

USB input

XLR input Con1
The board has two channels or inputs: CON1 and CON2. The first channel or CON1 is connected

to the Silver WBT RCA provided.
The second channel is optional – you can connect and XLR input or an SPDIF input or even a

USB

Содержание DAC5.1 Signature









































































































Результаты поиска

Содержание DAC5.1 Signature

Отзывы:

Похожие инструкции для DAC5.1 Signature

Бренды по названию

Популярные бренды

ANK DAC5.1 Signature, Руководство по монтажу

Результаты поиска

Содержание DAC5.1 Signature

Отзывы:

Похожие инструкции для DAC5.1 Signature

Бренды по названию

Популярные бренды