Analog Devices ADSP-21261 SHARC Скачать руководство пользователя страница 727

Страница: 727 / 846

ADSP-2126x SHARC Processor Hardware Reference

A-105

Registers Reference

Table A-30. SPIDMAC Register Bits

Bit(s)

Name

Function Type

Default

SPIDEN

DMA Enable.

Enables if set (= 1) or dis-

ables if cleared (= 0) DMA for the SPI
port.

Control

SPIRCV

DMA Direction.

When set, the IOP emp-

ties the RXSPI buffer, when cleared, the
IOP fills the TXSPI buffer.
0 = SPI Transmit DMA (Memory read)
1 = SPI Receive DMA (Memory write)

Control

INTEN

Enable DMA Interrupt

. Enables if set

(= 1) or disables if cleared (= 0) an inter-
rupt upon completion of the DMA trans-
fer.

Control

Reserved

SPICHEN

SPI DMA Chaining Enable

. Enables if set

(=1) or disables if cleared (= 0) DMA
chaining.

Control

6:5

Reserved

FIFOFLSH

DMA FIFO Flush.

Clears the four-deep

FIFO and FIFO status bits if set (= 1).
Once a one is written to this bit, it remains
set. A zero need to be written to clear this
bit.

Control

INTERR

Enable Interrupt on Error.

Enables if set

(= 1) or disables if cleared (= 0) an inter-
rupt when an error in the transmission
occurs.

Control

SPIOVF

Receive Overflow Error (SPIRCV=1).

Set

when SPIRCV = 1 and data is received
with the receive buffer full (1 = error data
received with receive data buffer RXSPI
full in receive mode DMA).

Status

SPIUNF

SPI Transmit Underrun Error.

Set when

SPIRCV = 0 and the SPI transmits without
any new data in the transmit buffer TXSPI.

Status

Содержание ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ADSP-21261 SHARC

Отзывы:

Analog Devices ADSP-21261 SHARC, Справочник по аппаратуре, Страница: 727 / 846

Результаты поиска

Содержание ADSP-21261 SHARC

Отзывы: