Analog Devices ADSP-21261 SHARC Скачать руководство пользователя страница 673 | Manualshive

Страница: 673 / 846

background image

ADSP-2126x SHARC Processor Hardware Reference

A-51

Registers Reference

Table A-17. Emulation Control Register (EMUCTL) Definitions

Bit #

Name

Function

0

EMUENA

Emulator Function Enable.

Enables processor emulation func-

tions. (0 = ignore breakpoints and emulator interrupts, 1=respond
to breakpoints and emulator interrupts)

1

EIRQENA

Emulator Interrupt Enable.

Enables the emulation logic to recog-

nize external emulator interrupts. (0 = disable, 1 = enable)

2

BKSTOP

Enable Autostop on Breakpoint.

Enables the

ADSP-2126x DSP to generate an external emulator interrupt
when any breakpoint event occurs. (0=disable, 1=enable)

3

SS

Enable Single Step Mode.

Enables single-step operation.

(0=disable, 1=enable)

4

SYSRST

Software Reset of the ADSP-2126x

. Resets the ADSP-2126x DSP

in the same manner as the external

RESET

pin. The SYSRST bit

must be cleared by the emulator.(0=normal operation, 1=reset)

5

ENBRKOUT

Enable the BRKOUT pin.

Enables the

BRKOUT

pin operation.

(0 =

BRKOUT

pin at high impedance state, 1 =

BRKOUT

pin enabled)

6

IOSTOP

Stop IOP DMAs in EMU Space.

Disables all DMA requests when

the DSP is in emulation space. Data that is currently in the SPI or
SPORT DMA buffers is held there unless the internal DMA
request was already granted. IOSTOP causes incoming data to be
held off and outgoing data to cease. Because SPORT receive data
cannot be held off, it is lost and the overrun bit is set.
(0 = I/O continues, 1 = I/O Stops)

7

Reserved

8

NEGPA1

Negate program memory data address breakpoint.

Enable break-

point events if the address is greater than the end register value OR
less than the start register value. This function is useful to detect
index range violations in user code.
(0 = disable breakpoint, 1 = enable breakpoint)
Instruction address and program memory breakpoint negates have
an effect latency of four (4) core clock cycles.

«
...
671
672
673
674
675
...
»

Содержание ADSP-21261 SHARC















































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADSP-21261 SHARC

SAFETank Series

Бренд: Raidon Страницы: 49

Бренд: CSS Страницы: 2

Teranex 2D Processor

Бренд: Blackmagicdesign Страницы: 969

TeleCLIENT TC7730 Series

Бренд: ETL Страницы: 83

Tamar FCSAS102800

Бренд: Bridgeworks Страницы: 56

Бренд: National Instruments Страницы: 52

MULTIflight Stick

Бренд: Multiplex Страницы: 10

Digital Loudspeaker

Бренд: Dolby Laboratories Страницы: 4

Бренд: Cowlacious Designs Страницы: 8

7798 I/SITE LAN

Бренд: CSI Страницы: 56

Бренд: ZALMAN Страницы: 9

ROScube-I Series

Бренд: ADLINK Technology Страницы: 95

Бренд: National Instruments Страницы: 37

Бренд: Exsys Страницы: 16

Бренд: LiveAction Страницы: 2

Бренд: Cisco Страницы: 26

Linksys WET610N

Бренд: Cisco Страницы: 78

Бренд: Cisco Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды