Amsco RELIANCE 444 HTM Скачать руководство пользователя страница 35

Страница: 35 / 36

5-7

Operational Test

Uncrating/Installation Instructions

P-920012-041

NOTE: Access to monitor PROG or FUNC menus is protected by a
pass code. Only authorized persons or a qualified technician may
have access to them.

IMPORTANT

: Independent Monitor Access Code is 2030.

1. Insert a virgin disk into Independent Monitor.

IMPORTANT:

Use good quality floppy disks only.

2. Format the disk. Refer to

Operator Manual

(P-920012-042)

Section 5, "Floppy Disk," 'Formatting a Floppy Disk' for instruc-
tions to format a disk.

NOTE: Never remove a disk from the drive while the drive light is on.

3. Program a File name. Refer to Operator Manual (P-920012-042)

Section 5 "Floppy Disk," 'Programming a Filename.'

4. Set the Independent Monitor to Trigger Mode. Refer to

Operator

Manual

(P-920012-042) Section 5 "Floppy Disk," 'Starting Data

Recording.'

5. Press

CYCLE START

and allow cycle to run to completion.

6. To verify if independent monitor has recorded the information,

remove floppy disk. Refer to Section 5, "Floppy Disk," 'Starting
Data Recording.'

7. Remove floppy disk and verify if information was recorded.

8. Refer to

Operator Manual

(P-920012-042) for procedure to visu-

alize information on a PC.

9. Insert a virgin disk. Follow steps 1 to 3.

10. Call Department Supervisor or authorized person to communi-

cate passcode on independent monitor.

NOTE: We suggest to keep the same factory-set passcode.

IMPORTANT:

Keep your passcodes safe. If you lose them, there is

NO WAY to clear or reset them.

12. If unit is automated (Load/Unload Modules), refer to

Uncrating/

Installation Instructions Manual

(P-122994-142) to install con-

veyor modules.

This unit is now ready for a thorough System Field Test,
Calibration, and a first-time Preventive Maintenance Check-
list Inspection by a qualified STERIS service representa-
tive.

Contact your STERIS Service Representative for availabil-

ity and information on this service. Refer to the

Maintenance

Manual

(P-764330-313) for further details on these procedures.

Start-up Procedure for

Independent Monitor

Set recording to Trigger Mode

Program a Filename

Format the disk

Insert a virgin disk into
Independent Monitor

Independent Monitor Start-Up

Flowchart

Содержание RELIANCE 444 HTM





































Результаты поиска

Содержание RELIANCE 444 HTM

Отзывы:

Бренды по названию

Популярные бренды

Amsco RELIANCE 444 HTM, Руководство по установке

Результаты поиска

Содержание RELIANCE 444 HTM

Отзывы:

Бренды по названию

Популярные бренды