Ammann AV 70 X Скачать руководство пользователя страница 54

Страница: 54 / 162

AV 70 X

478320

400501

2.6. Machine basic functions control

LH cluster (25)

Fuel consumption gauge

AMN25

It signals current fuel level in the tank, when emptied to min the

red LED will flicker.

Counter of motohours actually worked

It will display the number of motohours the engine was running.

With the engine started the counter will begin counting the mo-

tohours.

Note

Counting the number of motohours does not depend on en-

gine rpm.

Parking brake indicator lamp

The indicator lamp ON will signal the parking brake has been

enabled.

AMN26

AMN1

AMN2

Seat switch indicator lamp

Indicator lamp will light ON when operator is not sitting on the

seat or when emergency brake has been enabled.

Indicator lamp for hydraulic oil pressure filter

fouled

AMN3

Indicator lamp ON signals filter element is fouled.

Immediately replace the filter element!

Battery recharging indicator lamp

Unless indicator lamp goes OFF, find a

defect!

Indicator lamp lighted ON during engine run will signal a de-

fect. Following 5 seconds the acoustic alarm will start, and after

2 minutes the engine will stall automatically – the Machine will

stop and parking brake will be enabled.

Check fuel level during Machine

operation.

Engine can be started once its defect has

been repaired!

It signals proper function of battery recharging. When switching

the key on the ignition box (12) over to “I” position the indicator

lamp shall go ON and following the start it must go OFF.

AMN4

Содержание AV 70 X



































































































































































Результаты поиска

Содержание AV 70 X

Отзывы:

Похожие инструкции для AV 70 X

Бренды по названию

Популярные бренды

Ammann AV 70 X, Руководство по эксплуатации

Результаты поиска

Содержание AV 70 X

Отзывы:

Похожие инструкции для AV 70 X

Бренды по названию

Популярные бренды