Ammann AV 70 X Скачать руководство пользователя страница 113

Страница: 113 / 162

107

AV 70 X

400169

478320

400111D

478320

400111

MAINTENANCE MANUAL

Start moving the Machine:

Indicator lamps on LH cluster shall go OFF:

•

Indicator lamp for the idle (neutral) of travel controller.

Brake alarm indicator.

Use sound signal to indicate the engine

start!
Before engine is started, check there

is no hazard of any person if engine is

started!
Use sound signal before Machine starts

moving and wait long enough to any

persons present can leave the area

round the Machine (space beneath the

Machine) in time!
Make sure the area in front and behind

the Machine is free, with no persons

present within thereof!

Emergency brake push button function:

Check whether emergency brake works (8).

•

The engine stalling.

•

Then the following indicator lamps on LH cluster remain

•

ON:

Seat switch indicator lamp.

Parking brake warning lamp.

Battery charging indicator.

Engine lubrication indicator - flickers.

When travel controller is shifted to neutral position (N) the

•

seat switch indicator lamp goes OFF, and idle indicator lamp

lights up. Now you can start the engine again.

During operation, check continuously

the instruments and indicator lamps.
Promptly repair any failures!

Содержание AV 70 X



































































































































































Результаты поиска

Содержание AV 70 X

Отзывы:

Похожие инструкции для AV 70 X

Бренды по названию

Популярные бренды

Ammann AV 70 X, Руководство по эксплуатации

Результаты поиска

Содержание AV 70 X

Отзывы:

Похожие инструкции для AV 70 X

Бренды по названию

Популярные бренды