background image

110

AV 70 X

400178

400611A

400615

3.6.  Lubrication and Maintenance Operations

Drain oil when hot – best upon operation 

completion. 
Use original filters only.
Use  recommended  oil  under  Section 

3.2.1, only.
To  not  overtighten  the  filter,  its  thread 

and gasket may get damaged.
Check the tightness.

Collect the oil drained, do not let oil soak 

into soil.
Dispose of oil compliant to regulations.
Store used filters in a separate container 

and handle them so these do not pollute 

the environment. 

Note

Fill up to the dipstick’s top division mark. Total sump capac-

• 

ity is 7 l (1,85 gal US).
When  oil  is  exchanged,  start  the  engine  and  let  it  run  at 

• 

higher idle rmp for 2 - 3 min.
Stop the engine and wait for ca 3 min until oil descends into 

• 

the crankcase, then check the proper oil level.

3.6.13.  Inspect engine cooling circuit

Check  the  cooling  circuit  tightness.  Confirm  no  pipes  are 

• 

damaged and no clamps are missing.

3.6.12.  Inspect engine induction manifold

Check the pipes and clamps.

• 

Do not operate the Machine if pipes and 

clamps are damaged!

Содержание AV 70 X



































































































































































Отзывы: