Ammann AV 70 X Скачать руководство пользователя страница 53

Страница: 53 / 162

AV 70 X

OPERATION MANUAL

Switch for constant speed and protection against

engine overload (18)

3185

Constant speed function:

It is used to maintain constant speed of the Machine when driv-

ing on flat surface, uphill, or downhill.
When control unit is switched ON the indicator lamp on cluster

(26) signals this function.
The driving speed corresponds to the degree of swing of travel

control (1) from neutral position (0), depending on speed poten-

tiometer (2) adjustment.

ANTISTALL function

It is used to protect the engine on steep grade or the Machine

not to sink in ground.
With the control unit switched ON the indicator lamp on cluster

(26) will signal this function. The control unit will automatically

lower the power take-off (PTO) through reducing the set speed

(rpm of travel hydraulic motor) independently on travel control

position. Thus the tractive force (of travel hydraulic motor) will

increase - engine will get relieved.

Adjust engine max rpm by means of ac-

celerator control (13) before turning ON

the switch!
When a hard terrain has been overcome,

turn OFF the switch!

Switch + hazard beacon indicator lamp (19)

- (optional)

592348

It is used to switch ON/OFF hazard beacon, indicator lamp in the

switch signals this function.

Alarm lights switch (20)

AMN24

It is used to turn ON/OFF alarm lights - indicator lamp in the

alarm lights switch and on clusters (25) and (26) will flicker to

signal this function.

Switch + indicator lamp for cabin’s additional

lights (21) - (optional)

596473

It is used to switch ON/OFF additional lights, indicator lamp in

the switch signals this function.

indicator lamp rear lights (22)

591668R

It is used to turn ON/OFF rear lights, indicator lamp in the switch

signals this function.

Indicator lamps for (dipped / distance) lights

(23)

591508

These lamps signal dipped or distance lights switched ON.

Infrathermometer (24) - (optional)

3044

It will be enabled through the key turned ON in the ignition

box (12) and it will measure through temperature sensor for a

bitumen surface rolled. The value measured is indicated in C°

degrees on display (24).

Содержание AV 70 X



































































































































































Результаты поиска

Содержание AV 70 X

Отзывы:

Похожие инструкции для AV 70 X

Бренды по названию

Популярные бренды

Ammann AV 70 X, Руководство по эксплуатации

Результаты поиска

Содержание AV 70 X

Отзывы:

Похожие инструкции для AV 70 X

Бренды по названию

Популярные бренды