Ammann AV 70 X Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 162

background image

73

AV 70 X

OPERATION MANUAL

2.7.3. Emergency stop of the Machine

Apply this in the event of failure where the engine is unable to be shut off via the key in the ignition box,

or through shifting the travel controls (1) to position (0)!

How to switch ON:

Press emergency brake button (8) and the Machine will brake, engine will turn OFF and the acoustic alarm will start.
On cluster (25) the indicator lamps for seat switch, parking brake, recharging will light up, and lubrication indicator lamp will start to

flicker.

How to switch OFF:

Turn the press button in the direction of arrows and the acoustic alarm will get turned OFF.
On cluster (25) the parking brake indicator lamp and neutral indicator lamp will remain ON.
Shift travel controls (1) to neutral (N) position, the Machine can be started again in this position.

Do NOT use emergency brake to stop or switch OFF the engine during normal operation of the

Machine!

2.7.4. How to stop the Machine and its engine

Press button (7) on travel control (1) to switch OFF vibration, indicator lamp on cluster (25) will go OFF.
Stop the Machine through shifting travel controls (1) to neutral (N) position.
Use accelerator control (13) to adjust idle engine speed.
Switch over the key in the ignition box (12) to “0“ position, and tilt back the ignition box lid to close it.

Do not stop hot engine instantly but keep it running idle for 3 minutes. The engine and turbocharger

will get cooled down slowly and evenly!
Travel controls (1) shall be always in neutral (N) position!
Switch OFF the battery disconnector during Machine shutdown!

2.7.5. Machine parking

Shut down the Machine on flat and solid surface at a point with no potential of natural hazard (landslides, possible flooding, etc.)
Following the engine stop, before leaving the Machine, please disconnect its battery disconnector (51).
Clean the Machine to remove dirt (scrapers and drums).
Make overall inspection of the Machine and repair any defects that have occurred during operation.
Lock the Machine covers and its cabin.

Do NOT stop hot engine instantly, but instead let it idle for 3 minutes. The engine and turbocharger will

cool down slowly and evenly!

«
...
77
78
79
80
81
...
»

Содержание AV 70 X



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AV 70 X

Бренд: DARKSTAR TECHNOLOGIES Страницы: 4

Бренд: TDW Страницы: 2

Бренд: Taurus Страницы: 25

Бренд: Vancare Страницы: 3

Бренд: Paitec Страницы: 14

Бренд: NORLUX Страницы: 2

Бренд: AcceleDent Страницы: 3

Бренд: Zero 88 Страницы: 32

Бренд: Gardner Bender Страницы: 8

Бренд: NARIKA Страницы: 2

Бренд: H-TEC Education Страницы: 16

Бренд: H-TEC Education Страницы: 12

Бренд: Vahterus Страницы: 31

Бренд: MAGSTIM Страницы: 86

Бренд: Össur Страницы: 16

Exoform Dorsal Night Splint

Бренд: Össur Страницы: 34

MIDORI ULB-50sc

Бренд: Ushio Страницы: 24

Бренд: Croplands Страницы: 168

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды