Ammann AV 70 X Скачать руководство пользователя страница 102

Страница: 102 / 162

AV 70 X

3.4. Lubrication and Maintenance Chart

After 20 hours of operation (daily)

3.6.1.

Engine oil level check

3.6.2.

Engine cooling liquid level check

3.6.3.

Inspect the engine belt

3.6.4.

Crankcase breather

3.6.5.

Inspect air filter vacuum valve

3.6.6.

Inspect fan condition

3.6.7.

Fuel level check

3.6.8.

Hydraulic tank oil level check

3.6.9.

Water tank refilling

3.6.10.

Inspect alarm and control devices

Following 250 hours of operation (after 3 months)

3.6.11.

Engine oil exchange

3.6.12.

Inspect engine induction manifold

3.6.13.

Inspect engine cooling circuit

3.6.14.

Inspect the battery

3.6.15.

Air filter sensor check

3.6.16.

Watering filter cleaning

3.6.17.

Machine lubrication

After 500 hours of operation (after 6 months)

3.6.18.

Engine fuel filter exchange

3.6.19.

Engine cooling liquid level check

Following 1000 hours of operation (after 1 year)

3.6.20.

Inspect engine belt

3.6.21.

Inspect the exhaust system

3.6.22.

Inspect the silencing system

3.6.23.

Clean the water tank

3.6.24.

Oil change in the gearboxes *

Содержание AV 70 X



































































































































































Результаты поиска

Содержание AV 70 X

Отзывы:

Ammann AV 70 X, Руководство по эксплуатации, Страница: 102 / 162

Результаты поиска

Содержание AV 70 X

Отзывы: