Ammann AV 70 X Скачать руководство пользователя страница 148

Страница: 148 / 162

142

AV 70 X

416034

416035

416034A

3.6. Lubrication and Maintenance Operations

HINGED SCRAPERS (optional)

The Machine is fitted with four hinged (tilting) scrapers.

•

Position the scrapers:

In position (1) the scraper is set in transport position.

•

In position (2) the scraper is set in working position.

•

When in working position, the scraper blade (3) is pressed

•

against the drum body (4) by means of gas struts (4).

Replace the blade:

When the blade becomes excessively worn, please lift off

•

the scraper, remove the bolts (5) and take off the blade (3)

along with the strip (6).
Proceed in reverse steps to reinstall a new blade.

•

At the same time always check the proper function of the

•

gas struts (4).

Only when the gas struts work properly

and the worn scraper blades are replaced

in time, this will provide you with perfect

drum cleaning!

Содержание AV 70 X



































































































































































Результаты поиска

Содержание AV 70 X

Отзывы:

Похожие инструкции для AV 70 X

Бренды по названию

Популярные бренды

Ammann AV 70 X, Руководство по эксплуатации

Результаты поиска

Содержание AV 70 X

Отзывы:

Похожие инструкции для AV 70 X

Бренды по названию

Популярные бренды