Ammann AV 70 X Скачать руководство пользователя страница 57

Страница: 57 / 162

AV 70 X

OPERATION MANUAL

RH Cluster (26)

Level height in sprinkling tank.

AMN27

It signals the actual level of water in the tank, and when emptied

to min the red LED will start to flash.

Cooling liquid indicator lamp

Indicator lamp lighted ON during engine run will signal a de-

fect. Following 5 seconds the acoustic alarm will start, and after

2 minutes the engine will stall automatically – the Machine will

stop and parking brake will be enabled.

Engine can only be started when failure

is repaired and cooling liquid refilled to a

limit specified!

Air conditioner indicator lamp

Indicator lamp signals air conditioner is ON (optional).

AMN14

CRAB mode indicator lamp

Indicator lamp signals the front run is set to CRAB mode.

AMN15

Indicator lamp for soft starting to move and stop-

ping to move

Indicator lamp ON signals the mode of soft starting to move and

stopping to move is ON.
Intermittent flashing of this indicator lamp signals an error code

for a defect within Machine travel system.

Shut down the Machine and call service

organization in respect of failure repair

on the Machine travel system!!!

AMN16

ASC indicator lamp

AMN17

Not connected.

Fuel filter indicator lamp

AMN18

Indicator lamp lighted ON signals water presence in fuel filter.

Engine glowing indicator lamp

AMN19

The lighted control lamp signals the engine heating.

Spreader indicator lamp

AMN20

This indicator lamp signals the spreader is ON (optional).

Indicator lamp to protect against engine over-

load (ANTISTALL)

AMN21

This indicator lamp signals the ANTISTALL is ON.

Sprinkling pump indicator lamp

AMN22

Indicator lamp signals sprinkling pump is ON.

Constant speed indicator lamp

This indicator lamp signals the constant speed mode is ON.

AMN23

Alarm lights indicator lamp

AMN24

This indicator lamp signals alarm lights are ON.

AMN13

Check water level in the tank during

Machine run.

If this indicator is ON, please clean the

fuel filter!

Содержание AV 70 X



































































































































































Результаты поиска

Содержание AV 70 X

Отзывы:

Похожие инструкции для AV 70 X

Бренды по названию

Популярные бренды

Ammann AV 70 X, Руководство по эксплуатации

Результаты поиска

Содержание AV 70 X

Отзывы:

Похожие инструкции для AV 70 X

Бренды по названию

Популярные бренды