M470039-01 REV-F
Page 62
1.
MAX VOLTAGE--------press ENTER key, input the ma ximum volta ge then press ENTER
2.
MIN VOLTAGE ---------press ENTER key, input the minimum volta ge then press ENTER.
3.
MAX CURRENT--------press ENTER key, input the ma ximum current then press ENTER.
4.
MIN CURREN-----------press ENTER key, input the minimum current then press ENTER.
5.
MAX RESISTANCE----press ENTER key, input the ma ximum resista nce then press ENTER
6.
MIN RESISTANCE-----press ENTER key, input the minimum resista nce then press ENTER
7.
MAX POWER----------- press ENTER key, input the ma ximum power then press ENTER
8.
MIN POWER------------ press ENTER key, input the minimum power then press ENTER
11.
CAL. PARAM.-----press ENTER key, input the MEASURE LOW/ MEASURE HI GH / TRAN. OFFSET, then
press ENTER.
1: LOW MEASURE POINT--press ENTER key, set the low mea sure count va lue then press ENTER.
2: HIGH MEASURE POINT-press ENTER key, set the high mea sure count va lue then press ENTER.
3: TRANSIENT OFFSET---- press ENTER key, set the tra nsient offset count then press ENTER.
12.
OSCILLATE-------press ENTER key, select the OSC. CONTROL/ OSC. DELAY, then press ENTER.
13.
BOOT INPUT--------press ENTER key, use
to select ON / OFF then press ENTER.
B: Profile Menu
- press ENTER key:
* Use
to select the next menu setting then press ENTER key to enter the selected menu.
* Use
CLEAR
key to ba ck spa ce or to correct the wrong va lue.
1.
RECALL----------pre ss ENTER key, use
to select the profile 0/1/2/3 then press ENTER to reca ll.
2.
SAVE----------press ENTER key, use
to select the profile 0/1/2/3 then press ENTER to sa ve.
3.
RESET---------press ENTER key, then press ENTER to reset.
C: Display Menu
- press ENTER key:
* Use
to select the next menu setting then press ENTER key to enter the selected menu.
* Use
CLEAR
key to ba ck spa ce or to correct the wrong va lue.
1. METER MODE---press ENTER key, use
to select displa y mode (V+I, V+P, V+C, V+R, I+P, I+C, I+R,
R+P, R+C, P+C, V+T, I+T, R+T, P+T, C+T) then press ENTER.
2. ‘C’ Value------press ENTER key, then input the C value in Ampere.
D: System Menu
- press ENTER key:
* Use
to select the next menu setting then press ENTER key t o enter the selected menu.
* Use
CLEAR
key to ba ck spa ce or to correct the wrong va lue.
1. GPIB ADDRESS--press ENTER key, use
to set the GPIB a ddress ( 0 – 31 ) then press ENTER.
2. RS-232 SPEED----press ENTER key, use
to set the BAUD RATE ( 2400 – 115200 ) then press ENTER.
1: LOW MEAS POINT
2: HIGH MEAS POINT
3: TRANS OFFSET
1: RECALL
2: SAVE
3: RESET
1: Meter Mode
2: ‘C’ Value
1: GPIB ADDRESS
2: RS-232 SPEED
3: SYNTAX MODE
4: EOS CODE
5: BUZZER
6: PANEL LOCK
7: ETHERNET
Содержание Amrel PLA 2U
