American Dryer Corp. PHASE 7 OPL Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 63

background image

26

SECTION V

L.E.D. DISPLAY MESSAGES

The L.E.D. display informs the operator of cycle status, program verification, and displays important diagnostic
messages and fault information.

A. L.E.D. DISPLAY OPERATING STATUS

1.

Cycles in Progress

a.

While the dryer is operating, the L.E.D. display will read which cycle is in progress. i.e., in a
Manual Drying Cycle (Mode), the L.E.D. display will read “MANUAL DRYING CYCLE”. In
the Cool Down Cycle (Mode) the L.E.D. display will read “COOL DOWN TEMP __, __ MINUTES
REMAIN”.

2.

Cycle Status

a.

While a cycle is in progress, the L.E.D. display will show the progress of the cycle that is

being processed.

1) Automatic Drying Cycle

a) While a cycle is in progress the cycle status will display ELAPSED TIME__MIN.

During the Drying Cycle, the Phase 7 OPL microprocessor controller (computer) is
monitoring the moisture in the load. Once the temperature is above 160 F, the Cycle Status
portion of the L.E.D. will change from ELAPSED TIME __ MIN to __% DRY. The
display will count upward until the percentage of extraction programmed is reached.

2) Timed (Manual) Drying Cycle

a) While a cycle is in progress the cycle status, will display __ MINUTES REMAIN.

3.

Alternate Display Programs

a.

The tumblers RPM can be displayed by pressing and holding the Down Arrow key while a cycle is
in progress. If a cycle is not in progress, the board voltage is displayed.

b.

The Tumbler temperature can be displayed by pressing and holding the Up Arrow key at any time.

«
...
27
28
29
30
31
...
»

Содержание PHASE 7 OPL
































































Отзывы:

Нет отзывов

Похожие инструкции для PHASE 7 OPL

MEDC700VJ - 27in Centennial Series Electric Dryer Oxide

Бренд: Maytag Страницы: 24

Professional 1 Slim

Бренд: Taurus Страницы: 68

Бренд: Biodrier Страницы: 6

Бренд: Amana Страницы: 2

Бренд: GE Страницы: 60

Бренд: GE Страницы: 40

Бренд: Hotpoint Страницы: 16

Бренд: LG Страницы: 38

Бренд: LG Страницы: 41

Бренд: LG Страницы: 16

Бренд: LG Страницы: 32

Бренд: LG Страницы: 2

Бренд: LG Страницы: 2

Бренд: LG Страницы: 45

Бренд: LG Страницы: 2

Бренд: LG Страницы: 32

Бренд: LG Страницы: 62

Бренд: LG Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды