American Dryer Corp. PHASE 7 OPL Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 63

background image

16

O. PROGRAM LOCATIONS

This is where system parameters are programmed. These system parameters (programs) are stored in memory.
Access to this location is acquired by pressing the “CLEAR/STOP” and the “UP-ARROW” together. To exit
the Programming Location, simply press the “CLEAR/STOP” key. If you are several menu layers deep,
continue to press the “CLEAR/STOP” key until you are all the way out of the programming mode.

0.

SELECT LANGUAGE - This menu allows the selection of 5 different languages to operate the dryer.
The language that is selected will be used for every displayed message as well as Faults and Menus.

ENGLISH
FRANCAIS
ESPANOL
ITALIANO
DEUTSCH

1.

SELECT SYSTEM PARAMETERS - This menu level has 4 sections . All programmable parameters
other than preprogrammed cycles are done here.

0.

DRYER SETUP - All parameters that pertain to drying are in this menu level.

0. SELECT MODEL - This allows the selection of the heat source applied to

the dryer.

GAS DOUBLE BURNER
GAS SINGLE BURNER
STEAM

1. SYSTEM TEMP - This selection controls whether the temperature-related

programs will be operated in Fahrenheit (ºF) or Celsius (ºC). The programs
affected are as follows:

1) Temperature Display Mode.

2) Temperature Selections (drying temperatures).

3) Cool Down Temperatures.

IMPORTANT:

The Phase 7 OPL microprocessor controller (computer) automatically calculates and
converts the temperatures in these programs to the previously set value. For example,
when changing from ºF to ºC, if the preprogrammed Cycle “A” drying temperature was
set for 160ºF,the Phase 7 OPL microprocessor controller (computer) will change to
71ºC (+/- one-degree Celsius).

«
...
17
18
19
20
21
...
»

Содержание PHASE 7 OPL
































































Отзывы:

Нет отзывов

Похожие инструкции для PHASE 7 OPL

Бренд: Clatronic Страницы: 52

Бренд: UFESA Страницы: 26

Бренд: V-ZUG Страницы: 48

Бренд: Presto Страницы: 9

Бренд: RAMTONS Страницы: 7

Бренд: GE Страницы: 60

Бренд: YEDI Страницы: 14

Бренд: GEAppliances Страницы: 144

Бренд: Beko Страницы: 32

Бренд: Beko Страницы: 28

Бренд: Beko Страницы: 72

Бренд: Beko Страницы: 68

Бренд: Beko Страницы: 52

Бренд: Beko Страницы: 36

Бренд: Beko Страницы: 68

Бренд: Beko Страницы: 60

Бренд: Beko Страницы: 32

Бренд: Beko Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды