American Dryer Corp. PHASE 7 OPL Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 63

background image

10

D. TIMED (MANUAL) DRYING CYCLE OPERATION (Mode)

This drying cycle is intended for special loads where a specific amount of drying time and cooling time is
needed, especially for fine, delicate items which require very low temperatures and long drying and/or cool
down time periods.
All the parameters set in “COOL DOWN SETUP” pertain to the Manually loaded Manual and Auto
cycles. The (A-F) and (0-99) cycles that have been selected to be Manual, have separate settings for all the
parameters contained in the “COOL DOWN SETUP” menu

Timed (Manual) Cycle (Mode) Selections:

1) Drying Time - programmable from 0 to 99 minutes in one-minute increments.

2) Cool Down Time - programmable from 0-99 minutes in one-minute increments.

3) Drying Temperature - programmable from 100°F to 200°F in one-degree increments or from 37°C
to 93°C in one-degree increments.

4) For optional reversing, the Phase 7 OPL microprocessor controller can be programmed to reverse or no
reverse (single detection rotation). This is done in “DRYER SETUP”.

5) Wrinkle Guard is always active.

«
...
11
12
13
14
15
...
»

Содержание PHASE 7 OPL
































































Отзывы:

Нет отзывов

Похожие инструкции для PHASE 7 OPL

Бренд: CPG Страницы: 13

Бренд: Marta Страницы: 8

Бренд: T-Fal Страницы: 46

Бренд: Trotec Страницы: 19

Бренд: Danby Страницы: 44

Profile PTD70EBMTWS

Бренд: GE Страницы: 20

Бренд: GE Страницы: 36

Бренд: DeLonghi Страницы: 9

Бренд: AEG Страницы: 52

Бренд: AEG Страницы: 48

Бренд: AEG Страницы: 100

Бренд: LG Страницы: 36

Бренд: LG Страницы: 62

Бренд: Beko Страницы: 76

Zanussi TCE 7127 W

Бренд: Electrolux Страницы: 18

Бренд: Electrolux Страницы: 12

Бренд: Electrolux Страницы: 31

Бренд: Electrolux Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды