American Dryer Corp. PHASE 7 OPL Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 63

background image

12

NOTE:

The Cool Down Cycle will run either until the Cool Down Temperature is reached or until
the Cool Down Time has expired, whichever comes first.

NOTE

: If there has been no Drying Time selected, then the Cool Down Cycle will ignore the Cool Down

Temp and do the Cool Down Time only.

G. L.E.D. DOT MATRIX DISPLAY

The L.E.D. (light emitting diode) display informs the user of cycle status, program verification, and displays
important diagnostic and fault information. A complete listing of the various display messages and their
meanings are shown on

page 27 - 29

of this manual.

Display Selections:

0 . Scroll Mode

a. Pixel - This mode will scroll every message, (that exceeds the display limit) from left to right

dropping off a pixel column at a time.

b. Character - This mode will scroll every message, (that exceeds the display limit) from left to right

dropping off a character at a time.

1 . Scroll Type

a. One Time - This will scroll the message once and stop at the beginning of the message.
b. Continuous With Pause - This will scroll the message then pause a brief second at the beginning of

the message before scrolling again. This will happen continuously.

c. Continuous - This will scroll the message continuously without a brief pause at the beginning of the

message.

2.

Scroll Speed 1 to 20
1 being the slowest and 20 being the fastest.

Cycle in Progress Display Status

During the Drying cycle, the display will indicate the type of cycle in progress by presenting

either one of the following:

1.

“AUTO DRYING CYCLE” - Manually Loaded Auto Cycle

2.

“AUTO DRYING CYCLE #” - The “#” is replaced with (A-F) or (0-99)

3.

“MANUAL DRYING CYCLE” - Manually Loaded Manual Cycle

4.

“MANUAL DRYING CYCLE #” - The “#” is replaced with (A-F) or (0-99)

«
...
13
14
15
16
17
...
»

Содержание PHASE 7 OPL
































































Отзывы:

Нет отзывов

Похожие инструкции для PHASE 7 OPL

Professional 1 Slim

Бренд: Taurus Страницы: 44

Professional 1 Slim

Бренд: Taurus Страницы: 60

STUDIO 2400 IONIC

Бренд: Taurus Страницы: 36

Charmant VT-1342 B

Бренд: Vitek Страницы: 16

Бренд: Lavex Страницы: 12

Бренд: DeLonghi Страницы: 9

Classic FP5500P

Бренд: Sunbeam Страницы: 36

Бренд: Kenwood Страницы: 42

Бренд: Hotpoint Страницы: 16

Бренд: Frigidaire Страницы: 8

Бренд: Tricity Bendix Страницы: 14

Бренд: Tricity Bendix Страницы: 28

Бренд: elvita Страницы: 74

Бренд: Caple Страницы: 10

Бренд: Caple Страницы: 12

Бренд: Indesit Страницы: 12

Бренд: Electrolux Professional Страницы: 28

Бренд: Remington Страницы: 67

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды