American Dryer Corp. PHASE 7 OPL Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 63

background image

18

6. ENTER AUDIO ALERT ON TIMES 0 TO 10 - This selection allows the operator to adjust
the amount of signal tones. This parameter (program) affects the tone at the end of the Cool
Down cycle, as well as, at the end of the Wrinkle Guard cycle.

1. DISPLAY SETUP - All parameters that pertain to the display is in this menu

level.

0. SELECT SCROLL MODE - The operator has the choice of having the display scroll each
Pixel (vertical line) or Character (letter).

1. SELECT SCROLL TYPE - The operator has the choice of scroll type as follows:

CONTINUOUS WITH PAUSE - This will continually scroll the message with a

pause at the beginning.

CONTINUOUS - This will continually scroll without pausing at the beginning of

the message.

ONE TIME - This will only scroll the message once and stop at the beginning for

the message.

2. SELECT SCROLL SPEED 1 TO 20 - 1=slowest and 20=fastest

2 COOL DOWN SETUP - The parameters that pertain to the Cool Down is in this menu level.

0. ENTER COOL DOWN TIME 0 TO 99 MINUTES - This parameter (program) affects
ONLY the Automatic Drying Cycle

(Patent No. 4,827,627)

when the manually loaded cycle

is selected.

1. ENTER COOL DOWN TEMPERATURE - This parameter (program) affects ONLY the

Automatic

Drying Cycle

(Patent No. 4,827,627)

when the manually loaded cycle is

selected. The Cool

Down Temperature is programmable from 70ºF to 100ºF in one-

degree increments and from

20ºC to 37ºC in one-degree increments.

2. ENTER SPIN TIME 30 TO 120 SECONDS - This parameter (program) is fixed at 2-1/2
minutes in the Forward direction and 2 minutes in the Reverse direction for the Automatic
Mode. In the Manual Mode, it is programmable. This Spin Time is programmed here for the
manually loaded Manual Cycle only.

3. ENTER STOP TIME 7 TO 10 SECONDS - This parameter (program) is fixed at 7 seconds
in the Automatic Mode and programmable in the Manual Mode. This Stop (Dwell) Time is
programed here for the manually loaded Manual Cycle only.

3. WRINKLE GUARD SETUP - The parameters that pertain to the Wrinkle Guard is in this menu

level.

0. WRINKLE GUARD AUDIO ALERT - This parameter (program) allows the operator to
turn the Audio Alert tone On or Off at the end of each Wrinkle Guard Cycle. The Amount is
the same that is selected in Dryer Setup for AUDIO ALERT ON TIME 0 TO 10.

AUDIO ALERT ON
AUDIO ALERT OFF

«
...
19
20
21
22
23
...
»

Содержание PHASE 7 OPL
































































Отзывы:

Нет отзывов

Похожие инструкции для PHASE 7 OPL

Бренд: Maytag Страницы: 7

Бренд: anko Страницы: 11

Бренд: Modernhome Страницы: 43

Бренд: Flame Страницы: 2

Бренд: Noble & Price Страницы: 4

Бренд: Roper Страницы: 16

Бренд: RUSTA Страницы: 68

Бренд: Conair Страницы: 330

Бренд: Carlton Страницы: 15

Бренд: Carolina Cooker Страницы: 32

Бренд: Hitachi Страницы: 200

Бренд: Tricity Bendix Страницы: 20

Бренд: Whirlpool Страницы: 52

Бренд: Whirlpool Страницы: 84

Бренд: Caple Страницы: 8

Бренд: Fagor Страницы: 82

Бренд: DeLonghi Страницы: 64

Бренд: Airflow Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды