American Dryer Corp. ML-122D Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 55

background image

50

SECTION X

BURNER AND BASKET (TUMBLER)/LINT CHAMBER

MANUAL RESET HI-LIMIT INSTRUCTIONS

(FOR PHASE 6 MODELS)

This dryer was manufactured with a burner manual reset hi-limit (gas models only) and basket (tumbler)/

lint chamber hi-limit thermostat, which is monitored by the Phase 6 computer. If either manual reset thermostat
is open prior to start of the drying cycle, the dryer will start momentarily and then shut down, the Phase 6
computer will display an error code with an audio indication. If the basket (tumbler)/lint chamber hi-limit thermostat
is open, the display will read “dRUM SAFETY FAIL.” If the burner hi-limit thermostat is open, the display will
read “bURNER SAFETY FAIL.”

If either manual reset hi-limit thermostat opens during a drying cycle, the display will show the applicable

error code described above along with an audio indication. If the drum temperature is above 100º F (38º C), the
dryer will continue to run with no heat for 3 minutes or until the drum temperature has flattened below 100º F
(38º C). The clear/stop button on the Phase 6 keyboard (touch pad)

must be

pressed to clear the error

condition. The open manual reset hi-limit thermostat

must be

reset “manually” prior to the start of the next

cycle.

This hi-temperature condition may be caused due to a restricted exhaust, poor airflow, or improper burner

operation.

The location of the burner hi-limit is on the right side of the burner box and the basket (tumbler) hi-limit is

located in the lint chamber area.

WARNING:

Discontinue power to dryer before attempting to reset hi-limit.

IMPORTANT

This dryer is equipped with a burner
hi-limit and tumbler/lint chamber hi-limit
thermostat which must be reset manually.

WARNING:

Discontinue power to dryer

before attempting to reset hi-limit.

ADC P/N:114093

«
...
52
53
54
55
»

Содержание ML-122D
























































Отзывы:

Нет отзывов

Похожие инструкции для ML-122D

Бренд: ASI JD MACDONALD Страницы: 6

Бренд: IRIT Страницы: 2

Бренд: Courmia Страницы: 20

Бренд: Van Air Systems Страницы: 12

Бренд: DeDietrich Страницы: 13

Бренд: Vitek Страницы: 24

PROFESSIONAL TDC111VG

Бренд: Asko Страницы: 28

Бренд: Kenmore Страницы: 8

Бренд: Kenmore Страницы: 8

Бренд: Kenmore Страницы: 4

Бренд: Stalgast Страницы: 16

Бренд: Panasonic Страницы: 10

Бренд: Zanussi Страницы: 16

Бренд: Zanussi Страницы: 16

Бренд: Zanussi Страницы: 12

Бренд: Zanussi Страницы: 16

Бренд: Zanussi Страницы: 11

Бренд: Zanussi Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды