American Dryer Corp. ML-122D Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 55

background image

11

10. The dryer

must be

installed with provisions for adequate combustion and make-up air supply.

CAUTION:

This dryer produces combustible lint and

must be

exhausted to the outdoors. Every 6

months, inspect the exhaust ducting and remove any lint build up.

B. UNPACKING/SETTING UP

Remove protective shipping material (i.e., plastic wrap, and/or optional shipping box) from dryer.

IMPORTANT:

Dryer

must be

transported and handled in an upright position at

ALL

times.

The dryer can be moved to its final location while still attached to the skid or with the skid removed. To un-skid
the dryer, locate and remove the four (4) lag bolts securing the base of the dryer to the wooden skid. Two (2) are
at the rear base, and two (2) are located in the bottom of the lint chamber. To remove the two (2) lag bolts
located in the lint chamber area, remove the lint drawer and the three (3) Phillips head screws securing the lint
door in place.

1. Leveling Dryer

a. To level the dryer, place 4-inch (10.16 cm) square metal shims (refer to the

illustration above

) or

other suitable material under the base pads. It is suggested that the dryer be tilted slightly to the rear.

«
...
13
14
15
16
17
...
»

Содержание ML-122D
























































Отзывы:

Нет отзывов

Похожие инструкции для ML-122D

DV9 BB94 Series

Бренд: Samsung Страницы: 56

Бренд: Frymaster Страницы: 2

Бренд: Belson Страницы: 2

Бренд: DAY Страницы: 49

AMBIANO MD 18762

Бренд: ALDI Страницы: 28

Бренд: DryMax Страницы: 12

Бренд: Hotpoint Страницы: 24

Бренд: Frigidaire Страницы: 8

796.51043 Series

Бренд: Kenmore Страницы: 16

Бренд: Kenmore Страницы: 16

Бренд: Kenmore Страницы: 15

24-Inch Wide/120-Volt LAUNDRY CENTER and

Бренд: Kenmore Страницы: 56

8873 - 24 in. Space Saver Laundry Center

Бренд: Kenmore Страницы: 24

Бренд: Kenmore Страницы: 15

27" (69 cm) Wide LAUNDRY CENTER Washer - Electric Dryer P/N 134809700A

Бренд: Kenmore Страницы: 15

Kenmore 27-1nch Wide - Extra Large Capacity Plus LAUNDRY CENTER Washer - Electric Dryer

Бренд: Kenmore Страницы: 32

Бренд: Kenmore Страницы: 28

Бренд: Kenmore Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды