American Dryer Corp. ML-122D Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 55

background image

33

NOTE:

During the purging period, check to be sure that

ALL

gas shutoff valves are open.

3) Once ignition is established, a gas pressure test

should be

taken at the gas valve pressure tap of

each dryer to assure that the water column (W.C.) pressure is correct and consistent.

NOTE:

Water column pressure requirements (measured at the gas valve pressure tap)...

Natural Gas ------------------- 3.5 inches (8.7 mb) water column.
Liquid Propane (L.P.) Gas ---- 10.5 inches (26.1 mb) water column.

IMPORTANT:

There is no regulator provided in an L.P. dryer. The water column pressure

must be

regulated at the source (L.P. tank) or an external regulator

must be

added to each

dryer.

b. Steam Models

1) Check to insure that the steam damper is functioning properly.

a) The steam damper should not “slam” (open or closed) when it reaches the end of (piston)

travel. Additionally, the steam damper should not bind and/or stop during travel. If either of
these conditions occur, the flow control

must be

adjusted. Refer to the

bottom illustration

on

page 30

for air adjustment instructions.

6. Make a complete operational check of

ALL

safety-related circuits (i.e., lint drawer switch, and sail switch

on gas models).

NOTE:

To check for proper sail switch operation, open the main door and while holding main door
switch plunger in, start the dryer. The dryer should start but the heat circuit

should not be

activated (on). If the heat (burner) does activate, shut the dryer off and make the necessary
adjustments.

7. A reversing basket (tumbler) dryer

should never be

operated with less than a 60 lb (27 kg) load (dry

weight). The size of the load will affect the coast-down and dwell (stop) times. The basket (tumbler) must
come to a complete stop before starting in the opposite direction.

a. Microprocessor Controller (Computer) Dryer Models

1) Spin and stop are not adjustable in the Automatic Mode and have been preprogrammed into the

microprocessor controller (computer) for 150-seconds spin time in the forward direction and
120-seconds in the reverse direction with a 5-second dwell (stop) time.

2) Spin and stop times are adjustable in the Manual (timed) Mode.

b. Dual Timer Dryer Models

1) Both spin time and dwell (stop) time are adjustable (refer to

page 43

).

«
...
35
36
37
38
39
...
»

Содержание ML-122D
























































Отзывы:

Нет отзывов

Похожие инструкции для ML-122D

Бренд: Fantech Страницы: 4

Бренд: Quincy Compressor Страницы: 12

Бренд: Intertek Страницы: 20

Бренд: saro Страницы: 13

Бренд: Ayce Страницы: 36

Бренд: PITSOS Страницы: 12

Бренд: Smeg Страницы: 16

Бренд: Mediclinics Страницы: 24

Бренд: Mediclinics Страницы: 32

Бренд: Kogan Страницы: 32

Бренд: Frigidaire Страницы: 4

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 9

Бренд: Frigidaire Страницы: 4

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 1

Бренд: Frigidaire Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды