American Dryer Corp. ML-122D Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 55

background image

29

4. Steam Damper Air System Connections

The MLS-122 is manufactured with a pneumatic (piston) damper system, which requires an external
supply of compressed air. The air connection is made to the steam damper solenoid valve, which is located
at the rear of the top console.

a. Air Requirements

b. Air Connection

Air connection to system --- 1/8” F.P.T.

c. No air regulator or filtration is provided with the dryer. External regulation/filtration of 80 PSI (5.51

bars)

must be

provided. It is suggested that a regulator/filter gauge arrangement be added to the

compressed air line just before the dryer connection. This is necessary to insure that correct and clean
air pressure is achieved.

5. Steam Damper System Operation

The MLS-122 steam damper, as shown in the

top illustration

(

Diagram 1

) on

page 30

, allows the coil to

stay constantly charged eliminating repeated expansion and contraction. When the damper is opened, the
air immediately passes through the already hot coil, providing instant heat to start the drying process. When
the damper is closed, ambient air is drawn directly into the basket (tumbler), allowing a rapid cool down.

Diagram 1

shows the damper in the heating (open) mode, allowing heat into the basket (tumbler).

Diagram 2

shows the damper in the cool down (closed) mode, pulling ambient air directly into the basket

(tumbler) without passing through the coils.

NOTE:

With the dryer off or with no air supply, the steam damper is in cool down mode as shown in

Diagram 2

(refer to the

illustration

on the following page).

COMPRESSED

AIR SUPPLY

AIR PRESSURE

Normal

80 PSI

5.51 bars

Minimum Supply

70 PSI

4.82 bars

Maximum Supply

90 PSI

6.21 bars

Shaded areas are stated in metric equivalents

«
...
31
32
33
34
35
...
»

Содержание ML-122D
























































Отзывы:

Нет отзывов

Похожие инструкции для ML-122D

Бренд: Haier Страницы: 7

HD80-01 WH HA AA

Бренд: Haier Страницы: 33

DV9 BB94 Series

Бренд: Samsung Страницы: 56

Бренд: Dean Страницы: 2

Бренд: Thermo Scientific Страницы: 45

Professional 1 Slim

Бренд: Taurus Страницы: 68

Бренд: NEFF Страницы: 32

MASTERJET J1C Series

Бренд: Frymaster Страницы: 44

Бренд: Alliance Laundry Systems Страницы: 32

Бренд: Electrolux Страницы: 40

Бренд: Electrolux Страницы: 24

Бренд: Electrolux Страницы: 44

Бренд: Electrolux Страницы: 36

Бренд: Electrolux Страницы: 44

Бренд: Electrolux Страницы: 48

Бренд: Electrolux Страницы: 52

Бренд: Electrolux Страницы: 52

Бренд: Electrolux Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды