American Dryer Corp. ML-122D Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 55

background image

32

8. Be sure the lint drawer is securely in place.

NOTE: LINT

DRAWER

MUST

BE

CLOSED

TO

ACTIVATE

THE

SAFETY

SWITCH

OTHERWISE

THE

DRYER

WILL

NOT

START

.

9. Rotate the basket (tumbler/drum) by hand to be sure it moves freely.

10. Check bolts, nuts, screws, terminals, and fittings for security.

11. STEAM MODELS - check to insure air supply (80 PSI [5.51 bars]) is connected to the dryer.

12. STEAM MODELS - check to insure

ALL

steam shutoff valves are open.

13. STEAM MODELS - check steam damper operation.

14. Check basket (tumbler) bearing setscrews to insure they are

ALL

tight.

K. PREOPERATIONAL TESTS

ALL

dryers are thoroughly tested and inspected before leaving the factory. However, a preoperational test

should be

performed before the dryer is publicly used. It is possible that adjustments have changed in transit or

due to marginal location (installation) conditions.

1. Turn on electric power to the dryer.

2. Make sure the main door is closed and the lint drawer is securely in place.

3. Refer to the Operating Instructions for starting your particular model dryer.

4. Check to insure that the basket (tumbler) starts in the clockwise (CW) direction. Additionally, check the

direction of the blower motor impellor (fan) to insure that the impellor (fan) rotates in the clockwise (CW)
direction as viewed from the front. If it is, the phasing is correct. If the phasing is incorrect, reverse two
(2) of the leads at L1, L2, or L3 of the power supply connections made to the dryer.

IMPORTANT:

Dryer blower motor impellor/fan as viewed from the front must turn in the clockwise
(CW) direction, otherwise the dryer efficiency

will

be

drastically reduced and

premature component failure can result.

5. Heat Circuit Operational Test

a. Gas Models

1) When the dryer is first started (during initial start-up), the burner has a tendency not to ignite on the

first attempt. This is because the gas supply piping is filled with air, so it may take a few minutes for
this air to be purged from the lines.

2) The dryer is equipped with a Direct Spark Ignition system, which has internal diagnostics. If

ignition is not established after the first attempt, the computer will go into retry mode. If ignition is
not established after two (2) retries, no heat condition occurs.

«
...
34
35
36
37
38
...
»

Содержание ML-122D
























































Отзывы:

Нет отзывов

Похожие инструкции для ML-122D

Бренд: Wahl Страницы: 128

Бренд: Dean Страницы: 2

Бренд: Morphy Richards Страницы: 8

TWEETY WB201302000W

Бренд: Mellerware Страницы: 6

Vision Tech VTV 580NC

Бренд: Hoover Страницы: 14

Бренд: LOCO COOKERS Страницы: 18

FreeZone 76700 Series

Бренд: Labconco Страницы: 65

Бренд: Tower Hobbies Страницы: 20

Бренд: Acekool Страницы: 68

Бренд: Adler Europe Страницы: 64

Бренд: Adler Europe Страницы: 64

Бренд: Adler Europe Страницы: 64

Бренд: Blue Seal Страницы: 35

Бренд: Cobra Страницы: 19

Бренд: GE Страницы: 4

Бренд: GE Страницы: 16

Бренд: GE Страницы: 15

Бренд: GE Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды