American Dryer Corp. ML-122D Скачать руководство пользователя страница 20

Страница: 20 / 55

ALL

ductwork

should be

smooth inside with no projections from sheet metal screws or other obstructions,

which will collect lint. When adding ducts, the duct to be added should overlap the duct to which it is to be
connected.

ALL

ductwork joints

must be

taped to prevent moisture and lint from escaping into the

building. Inspection doors

should be

installed at strategic points in the exhaust ductwork for periodic

inspection and cleaning of lint from the ductwork.

IMPORTANT:

Exhaust back pressure measured by a manometer in the exhaust duct

must be

no less

than 0 and

must not exceed

0.3 inches (0.74 mb) of water column (W.C.).

NOTE:

When the exhaust ductwork passes through a wall, ceiling, or roof made of combustible
materials, the opening

must be

2-inches (5.08 cm) larger than the duct (all the way around).

The duct

must be

centered within this opening.

a. Outside Ductwork Protection

1) To protect the outside end of the horizontal ductwork from the weather, a 90° elbow bent downward

should be

installed where the exhaust exits the building. If the exhaust ductwork travels vertically

up through the roof, it

should be

protected from the weather by using a 180° turn to point the

opening downward. In either case, allow at least twice the diameter of the duct between the duct
opening and the nearest obstruction.

IMPORTANT:

DO NOT

use screens, louvers, or caps on the outside opening of the exhaust

ductwork.

2. Single Dryer Venting

Where possible, it is suggested to provide a separate exhaust duct for each dryer. The exhaust duct

should

laid out in such a way that the ductwork travels as directly as possible to the outdoors with as few turns

as possible. It is suggested that the use of 90° turns in ducting be avoided; use 30° and/or 45° angles
instead. The shape of the exhaust ductwork is not critical so long as the minimum cross section area is
provided.

IMPORTANT:

Minimum duct size for a dryer is 16-inches (40.64 cm) for a round duct or 14-1/2” by
14-1/2” (36.83 cm by 36.83 cm) for a square duct.

THE DUCT SIZE

MUST

NOT

REDUCED ANYWHERE DOWNSTREAM OF THE DRYER

Содержание ML-122D
























































Результаты поиска

Содержание ML-122D

Отзывы:

Похожие инструкции для ML-122D

Бренды по названию

Популярные бренды

American Dryer Corp. ML-122D, Руководство по установке

Результаты поиска

Содержание ML-122D

Отзывы:

Похожие инструкции для ML-122D

Бренды по названию

Популярные бренды