American Dryer Corp. ML-122D Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 55

background image

23

G. GAS INFORMATION

It is your responsibility to have

ALL

plumbing connections made by a qualified professional to assure that the gas

plumbing installation is adequate and conforms to local and state regulations or codes. In the absence of such
codes,

ALL

plumbing connections, materials, and workmanship

must conform

to the applicable requirements of

the National Fuel Gas Code ANSI Z223.1-LATEST EDITION, or in Canada, the Canadian Installation Codes
CAN/CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-M91 (Liquid Propane [L.P.] Gas) or LATEST
EDITION.

IMPORTANT:

Failure to comply with these codes or ordinances, and/or the requirements stipulated
in this manual, can result in personal injury and improper operation of the dryer.

The dryer and its individual shutoff valves

must be

disconnected from the gas supply piping system during any

pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa). The dryer

must be

isolated

from the gas supply piping system by closing its individual manual shutoff valve during any pressure test of the
gas supply system at test pressures equal to or less than 1/2 psig (3.5 kPa).

IMPORTANT:

Failure to isolate or disconnect dryer from supply as noted can cause irreparable
damage to the gas valve, which will VOID THE WARRANTY.

WARNING: FIRE OR EXPLOSION COULD RESULT

.

1. Gas Supply

The gas dryer installation

must meet

the American National Standard...National Fuel Gas Code ANSI

Z223.1-LATEST EDITION, or in Canada, the Canadian Installation Codes CAN/CGA-B149.1 M91 (Natural
Gas) or CAN/CGA-B149.2-M91 (L.P. Gas) or LATEST EDITION, as well as local codes and ordinances
and

must be

done by a qualified professional.

NOTE:

Undersized gas piping will result in ignition problems, slow drying, increased use of energy, and
can create a safety hazard.

The dryer

must be

connected to the type of heat/gas indicated on the data label that is affixed to the left

side panel area behind the top control (access) door (refer to the

illustration

on

page 9

). If this information

does not agree with the type of gas available,

DO NOT OPERATE THE DRYER

.

Contact the reseller

who sold the dryer or the

ADC

factory.

IMPORTANT:

Any burner changes or conversions

must be

made by a qualified professional.

The input ratings shown on the dryer data label are for elevations up to 2,000 feet (610 meters), unless
elevation requirements of over 2,000 feet (610 meters) were specified at the time the dryer order was
placed with the factory. The adjustment or conversion of dryers in the field for elevations over 2,000 feet
(610 meters) is made by changing each burner orifice. If this conversion is necessary, contact the reseller
who sold the dryer or contact the

ADC

factory.

«
...
25
26
27
28
29
...
»

Содержание ML-122D
























































Отзывы:

Нет отзывов

Похожие инструкции для ML-122D

Бренд: Emerald Страницы: 32

Бренд: Wonderfire Страницы: 32

Бренд: Sanela Страницы: 4

Бренд: Braun Страницы: 4

Easy Pro Series

Бренд: TEFAL Страницы: 18

Бренд: Solt Страницы: 2

Бренд: Jata Beauty Страницы: 20

Cook Mate AF-D50-004A

Бренд: HAEGER Страницы: 64

Бренд: Klarstein Страницы: 76

Бренд: Christ Страницы: 107

Бренд: T3 Страницы: 19

Бренд: T-Fal Страницы: 24

Бренд: T-Fal Страницы: 28

Бренд: Mediclinics Страницы: 6

Бренд: Frigidaire Страницы: 2

MSW-IPD-1000-1W

Бренд: MSW Motor Technics Страницы: 11

Бренд: APRILIA Страницы: 16

iQ300 WK14D321HK

Бренд: Siemens Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды