American Dryer Corp. Gas/HSI & Steam ID-120 Скачать руководство пользователя

Страница: 36 / 54

8. Be sure the lint drawer is securely in place.

NOTE: LINT

DRAWER

MUST

CLOSED

ACTIVATE

THE

SAFETY

SWITCH

OTHERWISE

THE

DRYER

WILL

NOT

START

9. Rotate the basket (tumbler/drum) by hand to be sure it moves freely.

10. Check bolts, nuts, screws, terminals, and fittings for security.

11. STEAM MODELS - check to insure air supply (80 PSI [5.51 bars]) is connected to the dryer.

12. STEAM MODELS - check to insure

ALL

steam shutoff valves are open.

13. STEAM MODELS - check steam damper operation.

14. Check basket (tumbler) bearing setscrews to insure they are

ALL

tight.

K. PREOPERATIONAL TESTS

ALL

dryers are thoroughly tested and inspected before leaving the factory. However, a preoperational test

should be

performed before the dryer is publicly used. It is possible that adjustments have changed in transit or

due to marginal location (installation) conditions.

1. Turn on electric power to the dryer.

2. Make sure the main door is closed and the lint drawer is securely in place.

3. Refer to the Operating Instructions for starting your particular model dryer.

4. Check to insure that the basket (tumbler) starts in the clockwise (CW) direction. Additionally, check the

direction of the blower motor impellor (fan) to insure that the impellor (fan) rotates in the clockwise (CW)

direction as viewed from the front. If it is, the phasing is correct. If the phasing is incorrect, reverse two

(2) of the leads at L1, L2, or L3 of the power supply connections made to the dryer.

IMPORTANT:

Dryer blower motor impellor/fan as viewed from the front must turn in the clockwise

(CW) direction, otherwise the dryer efficiency

will

drastically reduced and

premature component failure can result.

5. Heat Circuit Operational Test

a. Gas Models

1) When the dryer is first started (during initial start-up), the burner has a tendency not to ignite on the

first attempt. This is because the gas supply piping is filled with air, so it may take a few minutes for

this air to be purged from the lines.

Содержание Gas/HSI & Steam ID-120























































Результаты поиска

Содержание Gas/HSI & Steam ID-120

Отзывы:

Похожие инструкции для Gas/HSI & Steam ID-120

Бренды по названию

Популярные бренды

American Dryer Corp. Gas/HSI & Steam ID-120, Руководство по установке

Результаты поиска

Содержание Gas/HSI & Steam ID-120

Отзывы:

Похожие инструкции для Gas/HSI & Steam ID-120

Бренды по названию

Популярные бренды