American Dryer Corp. Gas/HSI & Steam ID-120 Скачать руководство пользователя | Manualshive

Страница: 16 / 54

background image

12

2. If more headroom is needed when moving dryer into position, the top console (module) may be removed.

a. To Remove Top Console (Module)

1) Disconnect the ground wire (A) at the rear of dryer.

2) Remove the six (6) sets of nuts and washers (B) holding the console (module) to base. (Located

within control boxes.)

3) Open control door and control panel then disconnect the following:

a) On the right side box, disconnect the 4-pin plug as well as the 4-pin and 2-pin plug located on the

microprocessor controller (computer). Additionally, remove the air connection at the union, and

the two (2) ground wires connected to the dryer base.

b) On the left side box, disconnect the drive and blower motor wires, along with the 2-pin plug and

the three (3) ground wires (two [2] that go to the panel and one [1] that goes to the dryer base).

4) Lift the console (module) off the dryer base (C).

IMPORTANT:

The dryer

must be

transported and handled in an upright position at

ALL

times.

«
...
14
15
16
17
18
...
»

Содержание Gas/HSI & Steam ID-120























































Отзывы:

Нет отзывов

Похожие инструкции для Gas/HSI & Steam ID-120

Бренд: Oliver Страницы: 54

Бренд: Sencor Страницы: 5

Бренд: Paula Deen Страницы: 24

01.182037.01.001

Бренд: Princess Страницы: 16

Бренд: TEFAL Страницы: 32

Бренд: Zazen Страницы: 4

Бренд: Hotpoint Страницы: 16

Jet CXV TurboDryer F367

Бренд: Dri-Eaz Страницы: 11

Бренд: Kleenmaid Страницы: 24

Бренд: ORIGO Страницы: 2

Бренд: Crosley Страницы: 56

Бренд: Insignia Страницы: 19

Бренд: Vitek Страницы: 20

Бренд: Beko Страницы: 56

Бренд: GE Страницы: 3

GE Profile DCCB330EG

Бренд: GE Страницы: 3

Moisture monitor series 3

Бренд: GE Страницы: 99

Бренд: Caple Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды