American Dryer Corp. Gas/HSI & Steam ID-120 Скачать руководство пользователя

Страница: 21 / 54

IMPORTANT:

Exhaust back pressure measured by a manometer at each basket (tumbler) exhaust

duct area

must be

no less than 0 and

must not

exceed

0.3 inches (0.74 mb) of water

column (W.C.).

a. Ducting (Horizontal and Vertical)

1) For single dryer horizontal ducting the minimum duct size is 16-inches (40.64 cm) in diameter, the

duct run should not have more than one (1) elbow (including outside protection), and

must not

exceed

40 feet (12.2 meters) in total length. With single dryer vertical ducting, the minimum duct

size is 18-inches (45.72 cm) in diameter, the duct run should not have more than three (3) elbows

(including outside protection), and

must not

exceed

20 feet (6.1 meters) in total length.

IMPORTANT:

When the ductwork approaches the maximum limits as noted in this manual, a

professional heating, venting, and air conditioning (HVAC) firm

should be

consulted

for proper venting information.

ALL

ductwork

should be

smooth inside with no projections from sheet metal screws or other

obstructions, which will collect lint. When adding ducts, the duct to be added should overlap the

duct to which it is to be connected.

ALL

ductwork joints

must be

taped to prevent moisture and

lint from escaping into the building. Inspection doors

should be

installed at strategic points in the

exhaust ductwork for periodic inspection and cleaning of lint from the ductwork.

NOTE:

When the exhaust ductwork passes through a wall, ceiling, or roof made of combustible

materials, the opening

must be

2-inches (5.08 cm) larger than the duct (all the way around).

The duct

must be

centered within this opening.

Содержание Gas/HSI & Steam ID-120























































Результаты поиска

Содержание Gas/HSI & Steam ID-120

Отзывы:

Похожие инструкции для Gas/HSI & Steam ID-120

Бренды по названию

Популярные бренды

American Dryer Corp. Gas/HSI & Steam ID-120, Руководство по установке

Результаты поиска

Содержание Gas/HSI & Steam ID-120

Отзывы:

Похожие инструкции для Gas/HSI & Steam ID-120

Бренды по названию

Популярные бренды