American Dryer Corp. Gas/HSI & Steam ID-120 Скачать руководство пользователя | Manualshive

Страница: 17 / 54

background image

13

C. DRYER ENCLOSURE REQUIREMENTS

Even though a 30-inch (76.2 cm) clearance is acceptable, it is recommended that the rear of the dryer be

positioned approximately 3 feet (0.91 meters) from nearest obstruction (i.e. wall) for ease of installation,

maintenance, and service. Bulkheads and partitions

should be

made from noncombustible materials. The

clearance between the bulkhead header and the dryer

must be

a minimum of 4-inches (10.2 cm) and must not

extend more than 4-inches (10.2 cm) to the rear of the dryer front. The bulkhead facing

must not be

closed in

ALL

the way to the top of the dryer. A 2-inch (5.08 cm) clearance is required.

NOTE:

Bulkhead facing

should not be

installed until after dryer is in place. Ceiling area

must be

located a minimum of 12-inches (31 cm) above the top of the dryer.

NOTE:

When fire sprinkler systems are located above the dryers, a minimum of 18-inches (46 cm)

above the dryer console (module) is suggested. Dryers may be positioned sidewall to sidewall

however, 1 or 2-inches (2.54 or 5.08 cm) is suggested between dryers (or wall) for ease of

installation and maintenance. Allowances

must be

made for the opening and closing of the

control and lint doors.

«
...
15
16
17
18
19
...
»

Содержание Gas/HSI & Steam ID-120























































Отзывы:

Нет отзывов

Похожие инструкции для Gas/HSI & Steam ID-120

Бренд: UFESA Страницы: 62

Бренд: e-Ware Страницы: 4

Smart Fryer AF-123544.2

Бренд: emerio Страницы: 35

Бренд: Giani Страницы: 28

MAXX PLUS FT 47822 SS MAXX PLUS FT 47824 SS MAXX PLUS FT 50876 SS

Бренд: Kalorik Страницы: 40

Бренд: Starmix Страницы: 140

Бренд: Acekool Страницы: 68

Бренд: Champion Страницы: 41

Бренд: GE Страницы: 12

Бренд: GE Страницы: 16

Бренд: GE Страницы: 3

Бренд: GE Страницы: 3

Бренд: GE Страницы: 3

Бренд: GE Страницы: 23

CleanSpeak GTD81ESSJWS

Бренд: GE Страницы: 36

Бренд: GE Страницы: 56

CleanSpeak GTD81ESPJMC

Бренд: GE Страницы: 36

Бренд: GE Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды