American Dryer Corp. Gas/HSI & Steam ID-120 Скачать руководство пользователя

Страница: 44 / 54

SECTION VI

ROUTINE MAINTENANCE

A. CLEANING

A program and/or schedule

should be

established for periodic inspection, cleaning, and removal of lint from

various areas of the dryer, as well as throughout the ductwork system. The frequency of cleaning can best be

determined from experience at each location. Maximum operating efficiency is dependent upon proper air

circulation. The accumulation of lint can restrict this airflow. If the guidelines in this section are met, an

ADC

dryer will provide many years of efficient, trouble-free, and most importantly safe operation.

WARNING: LINT FROM MOST FABRICS IS HIGHLY COMBUSTIBLE

THE

ACCUMULATION OF LINT CAN CREATE A POTENTIAL FIRE HAZARD

WARNING: KEEP DRYER AREA CLEAR AND FREE FROM COMBUSTIBLE

MATERIALS, GASOLINE, AND OTHER FLAMMABLE VAPORS AND

LIQUIDS

NOTE: REMOVE

POWER

FROM

THE

DRYER BEFORE

PERFORMING

ANY

MAINTENANCE

THE

DRYER (cleaning the lint drawer is the only exception)

NOTE:

Suggested time intervals shown are for average usage which is considered six (6) to eight (8)

operational (running) hours per day.

IMPORTANT:

Dryer produces combustible lint and

must be

exhausted to the outdoors. Every 6

months, inspect the exhaust ducting and remove any lint build up.

CLEAN LINT FROM LINT DRAWER/SCREEN EVERY THIRD OR FOURTH LOAD

NOTE:

The frequency of cleaning the lint screens can best be determined from experience at each

location.

WEEKLY

Clean lint accumulation from the lint chamber, thermostat, and microprocessor temperature sensor (sensor

bracket) area.

WARNING: TO AVOID HAZARD OF ELECTRICAL SHOCK, DISCONTINUE

ELECTRICAL POWER SUPPLY TO THE DRYER

Содержание Gas/HSI & Steam ID-120























































Результаты поиска

Содержание Gas/HSI & Steam ID-120

Отзывы:

Похожие инструкции для Gas/HSI & Steam ID-120

Бренды по названию

Популярные бренды

American Dryer Corp. Gas/HSI & Steam ID-120, Руководство по установке

Результаты поиска

Содержание Gas/HSI & Steam ID-120

Отзывы:

Похожие инструкции для Gas/HSI & Steam ID-120

Бренды по названию

Популярные бренды