American Dryer Corp. Gas/HSI & Steam ID-120 Скачать руководство пользователя страница 22

Страница: 22 / 54

b. Outside Ductwork Protection

1) To protect the outside end of the horizontal ductwork from the weather, a 90° elbow bent downward

should be

installed where the exhaust exits the building. If the exhaust ductwork travels vertically

up through the roof, it

should be

protected from the weather by using a 180° turn to point the

opening downward. In either case, allow at least twice the diameter of the duct between the duct

opening and nearest obstruction.

IMPORTANT:

DO NOT

use screens, louvers, or caps on the outside opening of the exhaust

ductwork.

3. Multiple Dryer (Common) Venting

If it is not feasible to provide separate exhaust ducts for each dryer, ducts from individual dryers may be

channeled into a common main duct. The individual ducts should enter the bottom or side of the main

duct at an angle not more than 45° in the direction of airflow and

should be

spaced at least 48-3/4 (123.8

cm) apart. The main duct

should be

tapered, with the diameter increasing before each individual 16-inch

(40.64 cm) duct is added.

a. Multiple Dryer Venting

1) In case of multiple (common) dryer venting, the distance from the last dryer to the outside exhaust

outlet

must not

exceed

20 feet (6.1 meters), and not have more than one (1) elbow (including

outside protection).

2) The minimum size of the duct from each dryer into the common duct is 16-inches (40.64 cm), and

must not have more than one (1) elbow. The total duct run from the dryer to the common duct

must not exceed

15 feet (4.57 meters) in length.

IMPORTANT:

This dryer

is not

provided with a back draft damper. When exhausted into a multiple

(common) exhaust line, a back draft damper

must be

installed at each dryer duct.

IMPORTANT:

No more than four (4) dryers

should be

connected to one (1) main common duct.

The main duct may be any shape or cross-sectional area, so long as the minimum cross section area

is provided. The

illustration

page 19

shows the minimum cross-sectional area for multiple

dryer round or square venting. These figures

must be

increased 10 square inches (64.52 square

centimeters) when rectangular main ducting is used, and the ratio of duct width to depth

should not

greater than 3-1/2 to 1. These figures

must be

increased in proportion if the main duct run to

the last dryer to where it exhausts to the outdoors exceeds the maximum limits noted.

IMPORTANT:

For extended ductwork runs, the cross section area of the ductwork can only be

increased to an extent. Maximum proportional ductwork runs

cannot

exceed 20 feet

(6.1 meters) more than the original limitations of 20 feet (6.1 meters) with two (2)

elbows. When the ductwork approaches the maximum limits as noted in this manual,

a professional heating, venting, and air conditioning (HVAC) firm

should be

consulted

for proper venting information.

Содержание Gas/HSI & Steam ID-120























































Результаты поиска

Содержание Gas/HSI & Steam ID-120

Отзывы:

Похожие инструкции для Gas/HSI & Steam ID-120

Бренды по названию

Популярные бренды

American Dryer Corp. Gas/HSI & Steam ID-120, Руководство по установке

Результаты поиска

Содержание Gas/HSI & Steam ID-120

Отзывы:

Похожие инструкции для Gas/HSI & Steam ID-120

Бренды по названию

Популярные бренды